AA Alclad 6061 Liga de alumínio
Atualizações de dados
Este material conta com 127 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
AA Alclad 6061 Propriedades físicas
Temperatura
Este material conta com 127 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
AA Alclad 6061 Tratamento Térmico
- The times and temperatures are typical for various forms, sizes and methods of manufacture and may not exactly describe the optimum treatment for a specific item.
The nominal temperatures at which metal is heated (applies both for solution and precipitation heat treatment) should be attained as rapidly as possible and maintained ± 5°C of nominal during the time at temperature.
The time at precipitation heat treatment temperature will depend on time required for load to reach temperature. The times shown are based on rapid heating, with soaking time measured from the time the load reached within 5°C of the applicable temperature.
Material should be quenched from the solution heat-treating temperature as rapidly as possible and with minimum delay after removal from the furnace. Quenching is typically performed by immersion of wrought products in a cold water bath, although some forgings are quenched in hot-water. Quenching may be performed by alternative means such as total immersion in an aqueous polymer solution, liquefied gas, hot water, or boiling water, or by air blast or fog to minimize distortion provided samples from the material. The use of high-velocity high-volume jets of cold water is also effective for some materials.
For sheet
Temper T4: Solution heat treated at 530°C, quenched, naturally aged.
Temper T42: Solution heat treated at 530°C, quenched, naturally aged.
Temper T6: Solution heat treated at 530°C, quenched, precipitation heat treated at 160°C for 18 hours.
Temper T62: Solution heat treated at 530°C, quenched, precipitation heat treated at 160°C for 18 hours.
For plate
Temper T4 (applies only to tread plate): Solution heat treated at 530°C, quenched, naturally aged.
Temper T451: Solution heat treated at 530°C, quenched, naturally aged. Stress-relieved by stretching is required to produce a specified amount of permanent set subsequent to solution heat treatment.
Temper T42: Solution heat treated at 530°C, quenched, naturally aged.
Temper T6 (applies only to tread plate): Solution heat treated at 530°C, quenched, precipitation heat treated at 160°C for 18 hours.
Temper T651: Solution heat treated at 530°C, quenched, precipitation heat treated at 160°C for 18 hours. Stress-relieved by stretching is required to produce a specified amount of permanent set prior to any precipitation heat treatment.
Temper T62: Solution heat treated at 530°C, quenched, precipitation heat treated at 160°C for 18 hours.
AA Alclad 6061 Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
AA Alclad 6061 Materiais Equivalentes Internacionais
Exibindo 3 de 3 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 3 de equivalentes internacionais?
Veja todos as classes 3 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 3Referências Cruzadas
- -Composição
- 48Propriedades Mecânicas
- 30Propriedades físicas
- 1Tratamento térmico
- -Metalografia
- -Usinabilidade
- 13Tensão-Deformação
- -Conformabilidade
- 1Fadiga
- -Fratura
- 14Rastejante
- 14Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- 3Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- -Total de Fornecedores