PROPRIETARY WM H-19 Aços de ferramenta
Atualizações de dados
Este material conta com 25 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY WM H-19 Composição química
Ellwood Specialty Steel, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY WM H-19 Propriedades físicas
Temperatura
Este material conta com 25 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY WM H-19 Tratamento Térmico
- Forging: Heating for forging must be done slowly and uniformly. Soak through at 1900-2000°F (1038-1093°C), and reheat as often as necessary, stopping work when the temperature drops below 1650°F (899°C). After forging cool slowly in lime, mica, dry ashes or furnace. Should always be annealed after forging.
Annealing: Heat slowly to 1550-1600°F (843-871°C), hold until the entire mass is heated through, and cool slowly in the furnace (40°F (22°C) per hour) to about 1000°F (538°C), after which the cooling rate may be increased. Suitable precautions must be taken to prevent excessive carburization or decarburization.
Strain relieving: When desirable to relieve the strains of machining, heat slowly to 1050-1250°F (566-677°C), allow to equalize, cool in still air.
Preheat for hardening: Warm slightly before charging into the preheat furnace, which should be operating at about 1400-1500°F (760-816°C).
Hardening: After thorough preheating, transfer to the hardening furnace, operating at 2100-2200°F (1149-1204°C), depending upon the degree of hardening required for the application, and the size of the tool. Salt baths or controlled atmosphere furnaces are suggested to minimize surface carbon changes. Long soaking times at the hardening temperature are not recommended because of the danger of grain growth.
Quenching: Cool in air, oil, or a molten salt bath operating at 1000-1100°F (538-593°C). In the case of oil quenching, it is usually advisable to interrupt the quench after the part has lost color (1000-1200°F (538-649°C)) and continue cooling in still air. Cooling should continue to 150°F (66°C), or to where parts can be held in the bare hand, and then tempered immediately.
Tempering: Tempering practice may vary with size and application, but is usually performed in the temperature range of maximum secondary hardness or higher. Double tempering is recommended.
PROPRIETARY WM H-19 Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY WM H-19 Materiais Equivalentes Internacionais
Exibindo 1 de 1 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 1 de equivalentes internacionais?
Veja todos as classes 1 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 1Referências Cruzadas
- 5Composição
- 10Propriedades Mecânicas
- 7Propriedades físicas
- 1Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 1Total de Fornecedores