PROPRIETARY WM H-19 Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 25 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY WM H-19 Composizione chimica
Ellwood Specialty Steel, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY WM H-19 Proprietà fisiche
Temperatura
Questo materiale dispone di 25 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY WM H-19 Trattamento Termico
- Forging: Heating for forging must be done slowly and uniformly. Soak through at 1900-2000°F (1038-1093°C), and reheat as often as necessary, stopping work when the temperature drops below 1650°F (899°C). After forging cool slowly in lime, mica, dry ashes or furnace. Should always be annealed after forging.
Annealing: Heat slowly to 1550-1600°F (843-871°C), hold until the entire mass is heated through, and cool slowly in the furnace (40°F (22°C) per hour) to about 1000°F (538°C), after which the cooling rate may be increased. Suitable precautions must be taken to prevent excessive carburization or decarburization.
Strain relieving: When desirable to relieve the strains of machining, heat slowly to 1050-1250°F (566-677°C), allow to equalize, cool in still air.
Preheat for hardening: Warm slightly before charging into the preheat furnace, which should be operating at about 1400-1500°F (760-816°C).
Hardening: After thorough preheating, transfer to the hardening furnace, operating at 2100-2200°F (1149-1204°C), depending upon the degree of hardening required for the application, and the size of the tool. Salt baths or controlled atmosphere furnaces are suggested to minimize surface carbon changes. Long soaking times at the hardening temperature are not recommended because of the danger of grain growth.
Quenching: Cool in air, oil, or a molten salt bath operating at 1000-1100°F (538-593°C). In the case of oil quenching, it is usually advisable to interrupt the quench after the part has lost color (1000-1200°F (538-649°C)) and continue cooling in still air. Cooling should continue to 150°F (66°C), or to where parts can be held in the bare hand, and then tempered immediately.
Tempering: Tempering practice may vary with size and application, but is usually performed in the temperature range of maximum secondary hardness or higher. Double tempering is recommended.
PROPRIETARY WM H-19 Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY WM H-19
Visualizzazione di 1 risultati su 1.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 1 equivalenti internazionali?
Visualizza tutti i 1 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 1Riferimenti incrociati
- 5Composizione
- 10Proprietà meccaniche
- 7Proprietà fisiche
- 1Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 1Fornitori Totali