PROPRIETARY WM H-19 Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 25 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM H-19 Composición química
Ellwood Specialty Steel, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM H-19 Propiedades físicas
Temperatura
Este material cuenta con 25 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM H-19 Tratamiento Térmico
- Forging: Heating for forging must be done slowly and uniformly. Soak through at 1900-2000°F (1038-1093°C), and reheat as often as necessary, stopping work when the temperature drops below 1650°F (899°C). After forging cool slowly in lime, mica, dry ashes or furnace. Should always be annealed after forging.
Annealing: Heat slowly to 1550-1600°F (843-871°C), hold until the entire mass is heated through, and cool slowly in the furnace (40°F (22°C) per hour) to about 1000°F (538°C), after which the cooling rate may be increased. Suitable precautions must be taken to prevent excessive carburization or decarburization.
Strain relieving: When desirable to relieve the strains of machining, heat slowly to 1050-1250°F (566-677°C), allow to equalize, cool in still air.
Preheat for hardening: Warm slightly before charging into the preheat furnace, which should be operating at about 1400-1500°F (760-816°C).
Hardening: After thorough preheating, transfer to the hardening furnace, operating at 2100-2200°F (1149-1204°C), depending upon the degree of hardening required for the application, and the size of the tool. Salt baths or controlled atmosphere furnaces are suggested to minimize surface carbon changes. Long soaking times at the hardening temperature are not recommended because of the danger of grain growth.
Quenching: Cool in air, oil, or a molten salt bath operating at 1000-1100°F (538-593°C). In the case of oil quenching, it is usually advisable to interrupt the quench after the part has lost color (1000-1200°F (538-649°C)) and continue cooling in still air. Cooling should continue to 150°F (66°C), or to where parts can be held in the bare hand, and then tempered immediately.
Tempering: Tempering practice may vary with size and application, but is usually performed in the temperature range of maximum secondary hardness or higher. Double tempering is recommended.
PROPRIETARY WM H-19 Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM H-19 Materiales Internacionales Equivalentes
Mostrando 1 de 1 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 1 internacionales equivalentes?
Consulte los grados 1 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 1Referencias cruzadas
- 5Composición
- 10Propiedades mecánicas
- 7Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 1Proveedores Totales