PROPRIETARY Uddeholm Holdax Aços de ferramenta
Atualizações de dados
Este material conta com 37 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Holdax Composição química
Uddeholms AB, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Holdax Propriedades físicas
Temperatura
Este material conta com 37 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Holdax Tratamento Térmico
- Soft annealing: Protect the steel and heat through to 720°C (1330°F), holding time 2 hours. Cool in furnace at 28°C (50°F) per hour to 600°C (1110°F), then freely in air;
Stress tempering: After rough machining the tool should be heated through to 550°C (1020°F), holding time 2 hours, then cool freely in air;
Hardening: (The steel should be fully soft annealed before hardening.) Preheating temperature: 500-600°C (930-1110°F). Austenitizing temperature: 850°C (1560°F). The steel should be heated through to the austenitizing temperature and held at temperature for 30 minutes. Protect the tool against decarburization and oxidation during the hardening process;
Quenching media: Forced air/atmosphere (only for small tools), Oil, Martempering bath 450-550°C (840-1020°F) max. 4 minutes, then cool in forced air. In order to obtain the optimum properties, the cooling rate should be as fast as is concomitant with acceptable distortion. Temper the tool as soon as its temperature reaches 50-70°C (120-160°F).
Tempering: Choose the tempering temperature according to the hardness. Temper twice with intermediate cooling to room temperature. Lowest tempering temperature 180°C (360°F). Holding time at temperature minimum 2 hours.
Nitriding and Nitrocarburizing: before Nitriding material should be rough machined, stress tempered at 550°C (1020°F) and fine machined. Gas nitriding: at 510°C (950°F) for 10 h and depth of case 0.20 mm, 30 h and depth of case 0.30 mm, 60 h and depth of case 0.40 mm. Ion nitriding at 480°C (895°F) for 10 h and depth of case 0.20 mm, 30 h and depth of case 0.25 mm, 60 h and depth of case 0.35 mm. Nitrocarburizing and 580°C (1060°F) in gas for 2.5 h and depth of case 0.25 mm or salt bath for 1 h and depth of case 0.15 mm
PROPRIETARY Uddeholm Holdax Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Holdax Materiais Equivalentes Internacionais
Exibindo 1 de 11 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 11 de equivalentes internacionais?
Veja todos as classes 11 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 11Referências Cruzadas
- 6Composição
- 4Propriedades Mecânicas
- 10Propriedades físicas
- 1Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 5Total de Fornecedores