PROPRIETARY Uddeholm Holdax Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 37 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY Uddeholm Holdax Composizione chimica
Uddeholms AB, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY Uddeholm Holdax Proprietà fisiche
Temperatura
Questo materiale dispone di 37 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY Uddeholm Holdax Trattamento Termico
- Soft annealing: Protect the steel and heat through to 720°C (1330°F), holding time 2 hours. Cool in furnace at 28°C (50°F) per hour to 600°C (1110°F), then freely in air;
Stress tempering: After rough machining the tool should be heated through to 550°C (1020°F), holding time 2 hours, then cool freely in air;
Hardening: (The steel should be fully soft annealed before hardening.) Preheating temperature: 500-600°C (930-1110°F). Austenitizing temperature: 850°C (1560°F). The steel should be heated through to the austenitizing temperature and held at temperature for 30 minutes. Protect the tool against decarburization and oxidation during the hardening process;
Quenching media: Forced air/atmosphere (only for small tools), Oil, Martempering bath 450-550°C (840-1020°F) max. 4 minutes, then cool in forced air. In order to obtain the optimum properties, the cooling rate should be as fast as is concomitant with acceptable distortion. Temper the tool as soon as its temperature reaches 50-70°C (120-160°F).
Tempering: Choose the tempering temperature according to the hardness. Temper twice with intermediate cooling to room temperature. Lowest tempering temperature 180°C (360°F). Holding time at temperature minimum 2 hours.
Nitriding and Nitrocarburizing: before Nitriding material should be rough machined, stress tempered at 550°C (1020°F) and fine machined. Gas nitriding: at 510°C (950°F) for 10 h and depth of case 0.20 mm, 30 h and depth of case 0.30 mm, 60 h and depth of case 0.40 mm. Ion nitriding at 480°C (895°F) for 10 h and depth of case 0.20 mm, 30 h and depth of case 0.25 mm, 60 h and depth of case 0.35 mm. Nitrocarburizing and 580°C (1060°F) in gas for 2.5 h and depth of case 0.25 mm or salt bath for 1 h and depth of case 0.15 mm
PROPRIETARY Uddeholm Holdax Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY Uddeholm Holdax
Visualizzazione di 1 risultati su 11.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 11 equivalenti internazionali?
Visualizza tutti i 11 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 11Riferimenti incrociati
- 6Composizione
- 4Proprietà meccaniche
- 10Proprietà fisiche
- 1Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 5Fornitori Totali