PROPRIETARY Uddeholm Holdax Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 37 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Holdax Composición química
Uddeholms AB, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Holdax Propiedades físicas
Temperatura
Este material cuenta con 37 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Holdax Tratamiento Térmico
- Soft annealing: Protect the steel and heat through to 720°C (1330°F), holding time 2 hours. Cool in furnace at 28°C (50°F) per hour to 600°C (1110°F), then freely in air;
Stress tempering: After rough machining the tool should be heated through to 550°C (1020°F), holding time 2 hours, then cool freely in air;
Hardening: (The steel should be fully soft annealed before hardening.) Preheating temperature: 500-600°C (930-1110°F). Austenitizing temperature: 850°C (1560°F). The steel should be heated through to the austenitizing temperature and held at temperature for 30 minutes. Protect the tool against decarburization and oxidation during the hardening process;
Quenching media: Forced air/atmosphere (only for small tools), Oil, Martempering bath 450-550°C (840-1020°F) max. 4 minutes, then cool in forced air. In order to obtain the optimum properties, the cooling rate should be as fast as is concomitant with acceptable distortion. Temper the tool as soon as its temperature reaches 50-70°C (120-160°F).
Tempering: Choose the tempering temperature according to the hardness. Temper twice with intermediate cooling to room temperature. Lowest tempering temperature 180°C (360°F). Holding time at temperature minimum 2 hours.
Nitriding and Nitrocarburizing: before Nitriding material should be rough machined, stress tempered at 550°C (1020°F) and fine machined. Gas nitriding: at 510°C (950°F) for 10 h and depth of case 0.20 mm, 30 h and depth of case 0.30 mm, 60 h and depth of case 0.40 mm. Ion nitriding at 480°C (895°F) for 10 h and depth of case 0.20 mm, 30 h and depth of case 0.25 mm, 60 h and depth of case 0.35 mm. Nitrocarburizing and 580°C (1060°F) in gas for 2.5 h and depth of case 0.25 mm or salt bath for 1 h and depth of case 0.15 mm
PROPRIETARY Uddeholm Holdax Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Holdax Materiales Internacionales Equivalentes
Mostrando 1 de 11 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 11 internacionales equivalentes?
Consulte los grados 11 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 11Referencias cruzadas
- 6Composición
- 4Propiedades mecánicas
- 10Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 5Proveedores Totales