PROPRIETARY VP20ISOFS Stale narzędziowe
Aktualizacje danych
Ten materiał ma 126 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
PROPRIETARY VP20ISOFS Skład chemiczny
Villares Metals, Product Data Sheets,
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
PROPRIETARY VP20ISOFS Właściwości fizyczne
Temperatura
Ten materiał ma 126 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
PROPRIETARY VP20ISOFS Obróbka cieplna
- Annealing: Heat slowly and evenly to temperatures between 760 and 800°C, at a rate of 100°C/h, keeping 1 hour for every 25 mm of the largest section of the piece. Slowly cool in an oven (30°C/h) to 600°C; then cool in calm air.
Stress Relief: After machining with large material removal, stress relief is recommended, heating the molds slowly and evenly (100°C/h) up to 530°C, keeping 0.5 hour in temperature for each 25 mm of the largest section in the part. Regardless of the section, the minimum time must be 2 hours; then cool in calm air.
Quenching: During quenching, the surface of the molds must be protected against decarburization and oxidation. Heat slowly and evenly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitization temperature, between 840 and 860°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air.
Tempering: Tools should be tempered immediately after quenching, as soon as they reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. Tempering temperatures should be chosen as per desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension. Allow 1 hour for each inch of thickness.
Nitriding: It must be carried out after quenching and tempering, as long as the nitriding temperature is at least 50°C lower than the temperature of the last tempering.
PROPRIETARY VP20ISOFS Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
PROPRIETARY VP20ISOFS Międzynarodowe materiały równoważne
Wyświetlanie 15 ze 58 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych - zawsze należy zweryfikować przydatność względem specyfikacji obowiązującej dla danego zastosowania.
Potrzebujesz pełną listę 58 międzynarodowych odpowiedników?
Zobacz pełną listę 58 równoważnych materiałów wraz ze szczegółowym przyporządkowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 58Odniesienia
- 5Skład Chemiczny
- 1Właściwości Mechaniczne
- 3Właściwości Fizyczne
- 2Obróbka Cieplna
- -Metalografia
- -Obrabialność
- -Naprężenie-Odkształcenie
- -Plastyczność
- -Zmęczenie materiału
- -Pęknięcie
- -Pełzać
- -Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- -Korozja
- -Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 57Łączna liczba dostawców