PROPRIETARY VP20ISOFS Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 126 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISOFS Composición química
Villares Metals, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISOFS Propiedades físicas
Temperatura
Este material cuenta con 126 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISOFS Tratamiento Térmico
- Annealing: Heat slowly and evenly to temperatures between 760 and 800°C, at a rate of 100°C/h, keeping 1 hour for every 25 mm of the largest section of the piece. Slowly cool in an oven (30°C/h) to 600°C; then cool in calm air.
Stress Relief: After machining with large material removal, stress relief is recommended, heating the molds slowly and evenly (100°C/h) up to 530°C, keeping 0.5 hour in temperature for each 25 mm of the largest section in the part. Regardless of the section, the minimum time must be 2 hours; then cool in calm air.
Quenching: During quenching, the surface of the molds must be protected against decarburization and oxidation. Heat slowly and evenly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitization temperature, between 840 and 860°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air.
Tempering: Tools should be tempered immediately after quenching, as soon as they reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. Tempering temperatures should be chosen as per desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension. Allow 1 hour for each inch of thickness.
Nitriding: It must be carried out after quenching and tempering, as long as the nitriding temperature is at least 50°C lower than the temperature of the last tempering.
PROPRIETARY VP20ISOFS Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20ISOFS Materiales Internacionales Equivalentes
Mostrando 15 de 58 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 58 internacionales equivalentes?
Consulte los grados 58 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 58Referencias cruzadas
- 5Composición
- 1Propiedades mecánicas
- 3Propiedades físicas
- 2Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 57Proveedores Totales