PROPRIETARY CPM 1 V 工具鋼（ＩＳＯ仕様）
材料グループ:
鉄合金 / 工具鋼（ＩＳＯ仕様）
国 / 規格:
PROPRIETARY
データ更新
最新情報: 2025-10
更新の総数: 4
更新履歴
2023-06
2015-08
2014-03
この材料には 47 件の特性データがありますが、現在表示されているのは一部のみです。
登録して、温度や条件ごとの詳細データを含む全ての材料特性データにアクセスしましょう。
全ての材料データを見る ›
無料登録・すぐにアクセス
無料登録・すぐにアクセス
PROPRIETARY CPM 1 V 化学組成
基準
値
単位
CAS 番号
基準
C
値
≤ 0.5000
単位
%
CAS 番号
7440-44-0
基準
Cr
値
≤ 4.5000
単位
%
CAS 番号
7440-47-3
基準
Mo
値
≤ 2.7000
単位
%
CAS 番号
7439-98-7
ZAPP AG, Product Data Sheet,
材料の詳細な性能データをお探しですか？
全ての材料データを見る ›
無料登録・すぐにアクセス
無料登録・すぐにアクセス
PROPRIETARY CPM 1 V 物理的性質
温度
この材料には 47 件の特性データがありますが、現在表示されているのは一部のみです。
温度や条件ごとの詳細な物理データを閲覧
全ての材料データを見る ›
無料登録・すぐにアクセス
無料登録・すぐにアクセス
PROPRIETARY CPM 1 V 熱処理
- ANNEALING heated slowly and uniform to a temperature of 900 °C, maintain the temperature for 2 hours and allow to cool to 590 °C in the furnace at a cooling rate no faster than 15 °C. It is then further cooled in still air down to room temperature. The typical annealed hardness achieved by a soft annealing is approx. HB190. Stress relieving follows rough machining by heating to 600-700 °C. Once complete heat penetration has been reached, the material is allowed to cool in the furnace to approx. 500 °C followed by cooling in air. Hardening usually involves the use of 2 preheating stages (450 - 500 °C/ 850 - 900 °C). Immediately following this it is heated to the required austenitizing temperature of 1065 - 1120 °C. Maximum toughness is attained at a temperature of 1065 °C, whilst maximum wear resistance is attained at the temperature of 1120 °C. In order to achieve a corresponding degree of dissolution of the alloy elements, a minimum heat penetration time of 20 minutes for hardening at 1065 °C is recommended, or 15 minutes for hardening at 1120 °C. These holding times should be correspondingly adapted for thick or thin walled material cross-sections. QUENCHING Air, hot bath or interrupted oil quenching can be used. In case of vacuum heat treatment, due regard is to be given to applying an appropriate quenching rate (at least at 5 bar pressure). For attaining ideal toughness properties it is recommended to apply the bath quenching method. TEMPERING Immediately temper after the material has cooled down below 40°C. Triple tempering with a holding time of 2 hours in each stage at the tempering temperature is necessary. Normally CPM® 1 V® is tempered with a temperature range of 540 - 550 °C. SURFACE TREATMENTS it can be nitrided or PVD/ CVD coated.
- Annealed: Heat to 870-900°C, hold 2 hours, slow cool no faster than 15°C per hour to 595°C, then furnace cool or cool in still air to room temperature. Stress relieved: Annealed Parts: Heat to 595-705°C, hold 2 hours, then furnace cool or cool in still air. Hardened Parts: Heat to 15-30°C below original tempering temperature, hold 2 hours, then furnace cool or cool in still air. Hardened: Preheat: Heat to 840-870°C Equalize. Austenitize: 1065-1120°C, hold time at temperature 10-15 minutes. The lower austenitized temperature of 1065°C provides the best impact toughness. Quench: Positive pressure quench (2 bar minimum) to below 50°C, or salt or interrupted oil quench to about 540°C, then air cool to below 50°C. Salt bath treatment if practical will ensure maximum attainable toughness for a given hardened treatment. Temper: Three times at 540-550°C, 2 hours minimum each time.
PROPRIETARY CPM 1 V 機械的特性
温度
用途に最適な材料を選定 - デモを予約
- -相互参照
- 23成分
- 1機械的特性
- 14物理的特性
- 3熱処理
- 1金属組織
- -被削性
- -応力-ひずみ
- -成形性
- -疲労
- -破壊
- -クリープ
- -接合
- -コーティング
- -寸法
- -トライボロジ
- -腐食
- -時効
- -耐候性
- -照射
- 5総仕入先数