PROPRIETARY CPM 20CV Acciaio inox
Aggiornamenti dei dati
Questo materiale dispone di 99 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY CPM 20CV Composizione chimica
Latrobe Specialty Steel, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY CPM 20CV Proprietà fisiche
Temperatura
Questo materiale dispone di 99 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY CPM 20CV Trattamento Termico
- Hardening:
Preheating: Heat to 760-788°C (1400-1450°F) and equalize.
Austenitizing (High Heat): Heat rapidly from the preheat to a temperature to within 1071-1177°C (1960-2150°F). A lower austenitizing temperature will maximize impact toughness. A higher austenitizing temperature will maximize wear resistance and corrosion resistance. Soak at the austenitizing temperature for 30 minutes.
Quenching: Pressurized gas or warm oil. For pressurized gas, the furnace should have a minimum quench pressure of 4 bars. A quench rate of approximately 222°C (400°F) per minute to below 538°C (1000°F) is critical to obtain the desired properties. For oil, quench until black, about 482°C (900°F), then cool in still air to 66-51°C (150-125°F).
Cryogenic treatment: For austenitizing at 1149°C (2100°F) or higher, a cryogenic treatment is recommended after quenching to 66-51°C (150 to 125°F) to reduce retained austenite. Cool to -73°C (-100°F), remove from the cooling medium, and allow part to warm to ambient temperature in still air.
Tempering: Temper immediately after quenching, or after quenching and cryogenic treatment. Typical temperature range is 204-427°C (400-800°F). Hold at temperature for 1 hour 25.4 mm of thickness, 2 hours minimum, then air cool to ambient temperature. The typical service hardness is 56-59 HRC, although higher hardness may be used for increased wear resistance. Tempering between 427-583°C (800-1100°F) will decrease corrosion resistance and toughness.
Annealing: Annealing must be performed after hot working and before re-hardening. Heat at a rate not exceeding 222°C per hour (400°F per hour) to 1016-1038°C (1860-1900°F), and hold at temperature for 1 hour per 25.4 mm of maximum thickness, 2 hours minimum. Then cool slowly with the furnace at a rate not exceeding 17°C per hour (30°F per hour) to 538°C (1000°F). Continue cooling to ambient temperature in the furnace or in air. The resultant hardness should be approximately 30 HRC or lower.
PROPRIETARY CPM 20CV Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY CPM 20CV
Visualizzazione di 1 risultati su 2.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 2 equivalenti internazionali?
Visualizza tutti i 2 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 2Riferimenti incrociati
- 7Composizione
- 77Proprietà meccaniche
- 10Proprietà fisiche
- 1Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 2Fornitori Totali