PROPRIETARY CPM 20CV Aceros inoxidables
Actualizaciones de datos
Este material cuenta con 99 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 20CV Composición química
Latrobe Specialty Steel, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 20CV Propiedades físicas
Temperatura
Este material cuenta con 99 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 20CV Tratamiento Térmico
- Hardening:
Preheating: Heat to 760-788°C (1400-1450°F) and equalize.
Austenitizing (High Heat): Heat rapidly from the preheat to a temperature to within 1071-1177°C (1960-2150°F). A lower austenitizing temperature will maximize impact toughness. A higher austenitizing temperature will maximize wear resistance and corrosion resistance. Soak at the austenitizing temperature for 30 minutes.
Quenching: Pressurized gas or warm oil. For pressurized gas, the furnace should have a minimum quench pressure of 4 bars. A quench rate of approximately 222°C (400°F) per minute to below 538°C (1000°F) is critical to obtain the desired properties. For oil, quench until black, about 482°C (900°F), then cool in still air to 66-51°C (150-125°F).
Cryogenic treatment: For austenitizing at 1149°C (2100°F) or higher, a cryogenic treatment is recommended after quenching to 66-51°C (150 to 125°F) to reduce retained austenite. Cool to -73°C (-100°F), remove from the cooling medium, and allow part to warm to ambient temperature in still air.
Tempering: Temper immediately after quenching, or after quenching and cryogenic treatment. Typical temperature range is 204-427°C (400-800°F). Hold at temperature for 1 hour 25.4 mm of thickness, 2 hours minimum, then air cool to ambient temperature. The typical service hardness is 56-59 HRC, although higher hardness may be used for increased wear resistance. Tempering between 427-583°C (800-1100°F) will decrease corrosion resistance and toughness.
Annealing: Annealing must be performed after hot working and before re-hardening. Heat at a rate not exceeding 222°C per hour (400°F per hour) to 1016-1038°C (1860-1900°F), and hold at temperature for 1 hour per 25.4 mm of maximum thickness, 2 hours minimum. Then cool slowly with the furnace at a rate not exceeding 17°C per hour (30°F per hour) to 538°C (1000°F). Continue cooling to ambient temperature in the furnace or in air. The resultant hardness should be approximately 30 HRC or lower.
PROPRIETARY CPM 20CV Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM 20CV Materiales Internacionales Equivalentes
Mostrando 1 de 2 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 2 internacionales equivalentes?
Consulte los grados 2 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 2Referencias cruzadas
- 7Composición
- 77Propiedades mecánicas
- 10Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 2Proveedores Totales