ASTM A 522 Type II Acciai strutturali e da costruzione
Aggiornamenti dei dati
Questo materiale dispone di 23 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
ASTM A 522 Type II Composizione chimica
A522/A522M: 2026 / Flange, raccordi, valvole e parti in acciaio al nickel (8 e 9%) forgiato o laminato per basse temperature
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
ASTM A 522 Type II Proprietà fisiche
Temperatura
Questo materiale dispone di 23 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
ASTM A 522 Type II Trattamento Termico
- Quenching and tempering: Quenching in water: 802 ± 14°C (1475 ± 25°F), hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; quench by immersion in circulating water. Reheat until the forging attains a uniform temperature within the range from 566 - 607°C (1050 - 1125°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air or water quench, at a rate not less than 167°C/h (300°F/h).
Double Normalized and Tempered: Heat to a uniform temperature of 899°C (1650°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air. Reheat until the forging attains a uniform temperature of 788°C (1450°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air. Reheat to a uniform temperature within the range from 566 - 607°C (1050 -1125°F); hold at this temperature for a minimum time of 2.5 min/mm of thickness but in no case less than 30 min; cool in air or water quench, at a rate not less than 167°C/h (300°F/h).
When stress relieving is to be performed after fabrication, the recommended stress-relieving treatment is as follows: gradually and uniformly heat the steel to a temperature between 552 - 585°C (1025 - 1085°F); hold for a minimum of 2 h for thicknesses up to 25 mm. For thicknesses over 25 mm, a minimum additional holding time in the ratio of 2.5 min/mm of thickness in excess of 25 mm shall be added. Cool at a minimum rate of 167°C/h (300°F/h) to a temperature not exceeding 316°C (600°F).
ASTM A 522 Type II Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
ASTM A 522 Type II Materiali equivalenti internazionali
Visualizzazione di 3 risultati su 4.
Le categorie di equivalenza riflettono il confronto tra composizione chimica e proprietà meccaniche — verificare sempre l'idoneità rispetto alla specifica applicabile alla propria applicazione.
Hai bisogno dell'elenco completo dei 4 equivalenti internazionali?
Visualizza tutti i 4 gradi equivalenti con mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 4Riferimenti incrociati
- 6Composizione
- 8Proprietà meccaniche
- 4Proprietà fisiche
- 1Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- -Fornitori Totali