PROPRIETARY TENAX350 Acier pour outils
Mises à jour des données
Ce matériau a 187 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY TENAX350 Composition chimique
Villares Metals, Product Data Sheets,
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
PROPRIETARY TENAX350 Propriétés physiques
Température
Ce matériau a 187 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY TENAX350 Traitement thermique
- Recommendations to improve tool life: Before starting operation, pre-heat slowly between 250-300°C, to obtain thermal homogenization of core and surface. Apply periodic stress relieving during the use of tools.
Stress relief: Must be employed after machining and before hardening. The procedure employs slowly heating to 500-600°C and furnace cooling until 200°C. After tooling, the stress relief must employ a temperature 50°C lower than that of the last tempering.
Hardening: Preheat tools at 595/650°C and equalize. Continue heating at 815/850°C and equalize. Continue heating to hardening temperature at 990/1030°C. For higher toughness: 1010°C is suggested. Holding time after temperature equalization: 15 to 30 minutes.
Cooling:
a) Oil, hot quenching 500/550°C,
b) Forced air,
c) Vacuum with gas quenching.
Maximum obtainable hardness: 54 + 2 HRC.
Tempering: Tools must be tempered immediately after hardening, as soon as they reach 60°C. It is necessary, at least, double tempering; after each tempering, tools must be slowly cooled to room temperature. The first tempering treatment should be performed at least 540°C, and the other treatments between 540-650°C, depending on the desired hardness.
Nitriding: Nitriding must be employed after hardening and tempering, normally in temperatures between 500 and 560°C, since they are at least 50°C lower than the last tempering temperature. As the surface finishing influence the nitriding layer efficiency, it is recommended that the surface is carefully grinned and polished before the nitriding process.
Electro-erosion: When employed in heat treated dies or molds, it is recommended the removal of the altered layer with fine grinding wheel and tempering the die again in a temperature around 50°C lower than that of the last tempering.
PROPRIETARY TENAX350 Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
PROPRIETARY TENAX350 Matériaux équivalents internationaux
Affichage de 15 sur 84 résultats.
Les catégories d'équivalence reflètent une comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation par rapport à la spécification applicable à votre utilisation.
Besoin de la liste complète des 84 équivalents internationaux ?
Consultez les 84 nuances équivalentes avec une correspondance détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 84Références croisées
- 5Composition
- 1Propriétés mécaniques
- 13Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 82Fournisseurs totaux