PROPRIETARY VH13-ISO Acier pour outils
Mises à jour des données
Ce matériau a 231 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY VH13-ISO Composition chimique
Villares Metals, Product Data Sheets,
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
PROPRIETARY VH13-ISO Propriétés physiques
Température
Ce matériau a 231 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY VH13-ISO Traitement thermique
- Annealing: Soft annealing should be carried out by heating between 840 and 860°C for 2 hours, followed by slow cooling at 10/20°C per hour until 650°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress relieving: The indicated procedure is slow heating to 500/600°C (or 50°C lower than the tempering temperature in case of hardened tool), holding until complete homogenisation, and cooling (air or furnace) at least down to 200°C.
Hardening and Tempering: the indicated heat treatment temperatures are: Pre-heating (780 - 820°C), Hardening (1000 - 1040°C), Tempering (540 - 650°C). After preheating, tools must be carried to another furnace, holding 30 min after soaking (after tool is fully heated throughout).
Quenching may be done in:
a) Salt bath at 500/550°C.
b) Warm quenching oil.
c) Vacuum, with high pressure circulated gas.
d) Air blast.
Tempering temperatures should be suitable to the working condition, but 450/540°C range should be avoided because can cause excessive loss in toughness. Double tempering is required and after each one tools must cool down to room temperature. After soaking, holding time of at least 2h is necessary.
Surface treatments: Nitriding temperature should be at least 50°C lower than that of the tempering.
PROPRIETARY VH13-ISO Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
PROPRIETARY VH13-ISO Matériaux équivalents internationaux
Affichage de 15 sur 110 résultats.
Les catégories d'équivalence reflètent une comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation par rapport à la spécification applicable à votre utilisation.
Besoin de la liste complète des 110 équivalents internationaux ?
Consultez les 110 nuances équivalentes avec une correspondance détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 110Références croisées
- 6Composition
- 1Propriétés mécaniques
- 13Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 99Fournisseurs totaux