PROPRIETARY VH13-ISO Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 231 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VH13-ISO Composición química
Villares Metals, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VH13-ISO Propiedades físicas
Temperatura
Este material cuenta con 231 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VH13-ISO Tratamiento Térmico
- Annealing: Soft annealing should be carried out by heating between 840 and 860°C for 2 hours, followed by slow cooling at 10/20°C per hour until 650°C and, then, by air cooling. In this treatment, the use of protective atmosphere is important to avoid surface oxidation and decarburization.
Stress relieving: The indicated procedure is slow heating to 500/600°C (or 50°C lower than the tempering temperature in case of hardened tool), holding until complete homogenisation, and cooling (air or furnace) at least down to 200°C.
Hardening and Tempering: the indicated heat treatment temperatures are: Pre-heating (780 - 820°C), Hardening (1000 - 1040°C), Tempering (540 - 650°C). After preheating, tools must be carried to another furnace, holding 30 min after soaking (after tool is fully heated throughout).
Quenching may be done in:
a) Salt bath at 500/550°C.
b) Warm quenching oil.
c) Vacuum, with high pressure circulated gas.
d) Air blast.
Tempering temperatures should be suitable to the working condition, but 450/540°C range should be avoided because can cause excessive loss in toughness. Double tempering is required and after each one tools must cool down to room temperature. After soaking, holding time of at least 2h is necessary.
Surface treatments: Nitriding temperature should be at least 50°C lower than that of the tempering.
PROPRIETARY VH13-ISO Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VH13-ISO Materiales Internacionales Equivalentes
Mostrando 15 de 110 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 110 internacionales equivalentes?
Consulte los grados 110 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 110Referencias cruzadas
- 6Composición
- 1Propiedades mecánicas
- 13Propiedades físicas
- 2Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 99Proveedores Totales