ABS AB/3 Aciers moulés
Mises à jour des données
Ce matériau a 231 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
ABS AB/3 Composition chimique
Rules for Materials and Welding, Part 2; Chapter 3 Section 7; Materials for Machinery, Boilers, Pressure Vessels, and Piping; Steel Machinery Forgings, American Bureau of Shipping, 2021
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
ABS AB/3 Propriétés physiques
Température
Ce matériau a 231 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
ABS AB/3 Traitement thermique
- Castings are to be either fully annealed, normalized or normalized and tempered in a furnace of sample proportions to bring the whole casting to uniform temperature above the transformation range on the annealing or normalizing cycle. The furnaces are to be maintained and have adequate means for control and recording temperature. Castings are to be held soaking at the proper temperature for at least a length of time equivalent to 1 h/25.5 mm of thickness of the heaviest member.
No annealed casting is to be removed from the furnace until the temperature of the entire furnace charge has fallen to or below a temperature of 455°C (850°F). A sufficient number of thermocouples are to be connected to the furnace charge to measure and record that its temperature is adequately uniform, unless the temperature uniformity of the furnace can be verified at regular intervals.
Tempering is to be carried out at a temperature of not less than 550°C (1022°F). - Forgings are to be annealed, normalized or normalized and tempered.
Cooling prior to heat treatment: After forging and before reheating for heat treatment, the forgings are allowed to cool in a manner to prevent injury and to accomplish transformation.
Annealing: The forgings are to be reheated to and held at the proper austenitizing temperature for a sufficient time to effect the desired transformation and then be allowed to cool slowly and evenly in the furnace until the temperature has fallen to about 455°C (850°F) or lower.
Normalizing: The forgings are to be reheated to and held at the proper temperature above the transformation range for a sufficient time to effect the desired transformation and then withdrawn from the furnace and allowed to cool in air. Water sprays and air blasts may be specially approved for use to achieve more rapid cooling. The faster cooling rates are to be agreed to by the purchaser.
Tempering: The forgings are to be reheated to and held at the proper temperature, which will be below the transformation range, and are then to be cooled under suitable conditions to 315°C (600°F) or lower. The tempering temperature is not to be less than 550°C (1022°F).
Retreatment: The manufacturer may re-heat treat the forging, but not more than three additional times.
ABS AB/3 Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
ABS AB/3 Matériaux équivalents internationaux
Affichage de 15 résultats sur 95.
Les catégories d'équivalence reflètent la comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation avec la spécification applicable à votre application.
Besoin de la liste complète des 95 équivalents internationaux ?
Consultez les 95 nuances équivalentes avec une cartographie détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 95Références croisées
- 10Composition
- 37Propriétés mécaniques
- 3Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 84Fournisseurs totaux