ABS AB/3 Dökme çelikler
Veri güncellemeleri
Bu malzemenin 231 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklıklar ve koşullar genelinde ayrıntılı değerler de dahil olmak üzere tam malzeme özelliklerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/3 Kimyasal bileşim
Rules for Materials and Welding, Part 2; Chapter 3 Section 7; Materials for Machinery, Boilers, Pressure Vessels, and Piping; Steel Machinery Forgings, American Bureau of Shipping, 2021
Tam malzeme performans verilerini mi arıyorsunuz?
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/3 Fiziksel özellikler
Sıcaklık
Bu malzemenin 231 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklık ve koşullar genelinde ayrıntılı fiziksel özellik değerlerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/3 Isıl İşlem
- Castings are to be either fully annealed, normalized or normalized and tempered in a furnace of sample proportions to bring the whole casting to uniform temperature above the transformation range on the annealing or normalizing cycle. The furnaces are to be maintained and have adequate means for control and recording temperature. Castings are to be held soaking at the proper temperature for at least a length of time equivalent to 1 h/25.5 mm of thickness of the heaviest member.
No annealed casting is to be removed from the furnace until the temperature of the entire furnace charge has fallen to or below a temperature of 455°C (850°F). A sufficient number of thermocouples are to be connected to the furnace charge to measure and record that its temperature is adequately uniform, unless the temperature uniformity of the furnace can be verified at regular intervals.
Tempering is to be carried out at a temperature of not less than 550°C (1022°F). - Forgings are to be annealed, normalized or normalized and tempered.
Cooling prior to heat treatment: After forging and before reheating for heat treatment, the forgings are allowed to cool in a manner to prevent injury and to accomplish transformation.
Annealing: The forgings are to be reheated to and held at the proper austenitizing temperature for a sufficient time to effect the desired transformation and then be allowed to cool slowly and evenly in the furnace until the temperature has fallen to about 455°C (850°F) or lower.
Normalizing: The forgings are to be reheated to and held at the proper temperature above the transformation range for a sufficient time to effect the desired transformation and then withdrawn from the furnace and allowed to cool in air. Water sprays and air blasts may be specially approved for use to achieve more rapid cooling. The faster cooling rates are to be agreed to by the purchaser.
Tempering: The forgings are to be reheated to and held at the proper temperature, which will be below the transformation range, and are then to be cooled under suitable conditions to 315°C (600°F) or lower. The tempering temperature is not to be less than 550°C (1022°F).
Retreatment: The manufacturer may re-heat treat the forging, but not more than three additional times.
ABS AB/3 Mekanik özellikler
Sıcaklık
Doğru seçimi yapmak için eksiksiz mekanik özelliklere mi ihtiyacınız var?
Mukavemet, sertlik, yorulma ve daha fazlası hakkında eksiksiz verilere ulaşın.
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/3 Uluslararası eşdeğer malzemeler
95 sonuçtan 15 tanesi gösteriliyor.
Eşdeğerlik kategorileri kimyasal bileşim ve mekanik özellik karşılaştırmasını yansıtır — uygulamanız için uygunluğu her zaman geçerli şartnameye göre doğrulayın.
95 uluslararası eşdeğerin tam listesine mi ihtiyacınız var?
Standart, üretici ve eşdeğerlik kategorisine göre ayrıntılı eşleştirme ile 95 eşdeğer kaliteyi görüntüleyin.
Ücretsiz kayıt gereklidir • Anında erişim
Uygulamanız için en uygun olan malzeme seçiminizi optimize edin - Demo Rezervasyonu Yapın
- 95Çapraz Referanslar
- 10Bileşim
- 37Mekanik Özellikler
- 3Fiziksel Özellikler
- 2Isıl İşlem
- -Metalografi
- -İşlenebilirlik
- -Gerilme-Gerinim
- -Şekillendirilebilirlik
- -Yorulma
- -Kırılma
- -Sürünmek
- -Bağlantılar
- -Kaplamalar
- -Boyutlar
- -Triboloji
- -Korozyon
- -Yaşlanma
- -Hava şartlarına dayanıklılık
- -Radyasyon etkisi
- 84Toplam Tedarikçiler