SAE 4340 Mod Aciers de construction
Mises à jour des données
Ce matériau a 30 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
SAE 4340 Mod Composition chimique
SAE AMS 5330E: 1987 / Acier Pièces moulées, à la cire perdue 0.80Cr - 1.8Ni - 0.35Mo (0.38 - 0.46C) (SAE 4340 modifié) Recuit
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
SAE 4340 Mod Propriétés physiques
Température
Ce matériau a 30 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
SAE 4340 Mod Traitement thermique
- Annealed by heating to 845 +/- 15°C in an atmosphere neutral to the specified carbon range, holding at heat for not less than 1 hour and cooling as required. Hardened by heating, in an atmosphere neutral to the carbon content, to 815 +/- 15°C, holding at heat for not less than 30 minutes and quenching in oil, and double tempered by heating to a temperature not lower than 425°C, holding at heat for 2 hours +/- 0.25, and cooling in air, reheating to a temperature not lower than 425°C, holding at heat for 2 hours +/- 0.25, and cooling in air.
- Annealing temperature: 843°C (1550°F), cool at a rate not to exceed 111°C (200°F) per hour to below 538°C (1000°F). Normalizing temperature: 927°C (1700°F); Austenitizing temperature: 871°C (1600°F). Hardening quenchant: oil, polymer, inert gas. (Marquenching in a nitrate/nitrite salt bath, oil bath, or alternate quenchant operated at a set temperature applicable to the alloys processed is permitted. The parts shall be in the marquenching bath only for sufficient time to stabilize the parts at the bath temperature, but not less than 2 minutes, followed by cooling to approximately ambient temperature. Salt residues shall be removed by a hot water rinse before air tempering).
Tempering: 302°C (575°F), at least two tempering operations are required.
All parts, shall be in one of the following conditions prior to austenitizing: normalized, normalized or tempered or hardened. If those parts have been normalized only without tempering or overaging, they shall be preheated before exposure to the austenitizing temperature.
SAE 4340 Mod Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
SAE 4340 Mod Matériaux équivalents internationaux
Affichage de 5 résultats sur 5.
Les catégories d'équivalence reflètent la comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation avec la spécification applicable à votre application.
Besoin de la liste complète des 5 équivalents internationaux ?
Consultez les 5 nuances équivalentes avec une cartographie détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 5Références croisées
- 9Composition
- 7Propriétés mécaniques
- 3Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- 2Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 2Fournisseurs totaux