SAE 4340 Mod Aceros estructurales y de construcción
Actualizaciones de datos
Este material cuenta con 30 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
SAE 4340 Mod Composición química
SAE AMS 5330E: 1987 / Piezas Fundidas de Acero, de Precisión, 0.80Cr - 1.8Ni - 0.35Mo (0.38 - 0.46C) (SAE 4340 Modificado) Recocido
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
SAE 4340 Mod Propiedades físicas
Temperatura
Este material cuenta con 30 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
SAE 4340 Mod Tratamiento Térmico
- Annealed by heating to 845 +/- 15°C in an atmosphere neutral to the specified carbon range, holding at heat for not less than 1 hour and cooling as required. Hardened by heating, in an atmosphere neutral to the carbon content, to 815 +/- 15°C, holding at heat for not less than 30 minutes and quenching in oil, and double tempered by heating to a temperature not lower than 425°C, holding at heat for 2 hours +/- 0.25, and cooling in air, reheating to a temperature not lower than 425°C, holding at heat for 2 hours +/- 0.25, and cooling in air.
- Annealing temperature: 843°C (1550°F), cool at a rate not to exceed 111°C (200°F) per hour to below 538°C (1000°F). Normalizing temperature: 927°C (1700°F); Austenitizing temperature: 871°C (1600°F). Hardening quenchant: oil, polymer, inert gas. (Marquenching in a nitrate/nitrite salt bath, oil bath, or alternate quenchant operated at a set temperature applicable to the alloys processed is permitted. The parts shall be in the marquenching bath only for sufficient time to stabilize the parts at the bath temperature, but not less than 2 minutes, followed by cooling to approximately ambient temperature. Salt residues shall be removed by a hot water rinse before air tempering).
Tempering: 302°C (575°F), at least two tempering operations are required.
All parts, shall be in one of the following conditions prior to austenitizing: normalized, normalized or tempered or hardened. If those parts have been normalized only without tempering or overaging, they shall be preheated before exposure to the austenitizing temperature.
SAE 4340 Mod Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
SAE 4340 Mod Materiales equivalentes internacionales
Mostrando 5 de 5 resultados.
Las categorías de equivalencia reflejan la comparación de composición química y propiedades mecánicas — verifique siempre la idoneidad según la especificación aplicable a su aplicación.
¿Necesita la lista completa de 5 equivalentes internacionales?
Consulte los 5 grados equivalentes con mapeo detallado por norma, productor y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 5Referencias cruzadas
- 9Composición
- 7Propiedades mecánicas
- 3Propiedades físicas
- 2Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- 2Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 2Proveedores Totales