PROPRIETARY CarTech Ferrium C61 Alloy Aceros estructurales y de construcción
Actualizaciones de datos
Este material cuenta con 40 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech Ferrium C61 Alloy Composición química
Carpenter Technology Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech Ferrium C61 Alloy Propiedades físicas
Temperatura
Este material cuenta con 40 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech Ferrium C61 Alloy Tratamiento Térmico
- Normalizing: Heat uniformly to 1800°F (982°C) and air cool. Annealing: Heat uniformly to 1250°F (677°C), hold for 2 to 8 hours and air cool. Carburizing: Vacuum carburize at 1830°F (1000°C), followed by quenching in gas (1.5 Bar Nitrogen or higher) or oil medium. Quenching: Gas, Oil, Salt. Cold Treatment: A refrigeration treatment at -100°F (-73°C) or lower for 1 hour is recommended. This should be performed with minimal delay after completion of the quench. Straightening: Operations such as shaft straightening (if required) should preferably be done after the sub zero treatment but prior to the temper. C64 achieves full mechanical strength after tempering, and thus trying to straighten parts after tempering will be more difficult. If excessive distortion exists after the solution treatment, quench and sub-zero treatment, then it is recommended to heat the part to 392°F (200°C) in air for 1 hour, hot-straighten the part (temperature determined by amount of force required to straighten part; temperature should be maintained below 700F (371C) to avoid any tempering or decarburization; a small oxide layer may form at this temperature), and allow the component to air cool. The full temper cycle must then be applied. Tempering: Temper at 925°F (496°C) for 6 to 10 hours and air cool. It is preferred that tempering be performed in vacuum but can also be performed in air.
PROPRIETARY CarTech Ferrium C61 Alloy Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CarTech Ferrium C61 Alloy Materiales equivalentes internacionales
Mostrando 3 de 4 resultados.
Las categorías de equivalencia reflejan la comparación de composición química y propiedades mecánicas — verifique siempre la idoneidad según la especificación aplicable a su aplicación.
¿Necesita la lista completa de 4 equivalentes internacionales?
Consulte los 4 grados equivalentes con mapeo detallado por norma, productor y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 4Referencias cruzadas
- 7Composición
- 16Propiedades mecánicas
- 9Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 3Proveedores Totales