PROPRIETARY 2343 - H11 Aços de ferramenta
Atualizações de dados
Este material conta com 190 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY 2343 - H11 Composição química
Industeel, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY 2343 - H11 Propriedades físicas
Temperatura
Este material conta com 190 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY 2343 - H11 Tratamento Térmico
- Soft annealing: heat at 850°C (1560°F), cool down at 10°C (20°F) per hour until 650°C (1200°F), than air cool.
Stress relieving: after rough machining, stress in the tool can be released by heating at 650°C during 2 hours followed by air cooling.
Preheating (before austenitizing): heating rate should be limited to 220°C/h (400°F/h), measured in the core of cavity. First preheating has to be done at Ts = 620°C (1150°F) and hold until Ts-Tc < 110°C (200°F) Second preheating has to be done at Ts = 830°(1530°F) and hold until Ts-Tc < 15°C (25°F).
Austenitizing: after second preheating, austenitizing should be rapidly increased up to 1010°C (1850°F) and hold 30 mn after Ts-Tc < 15°C (25°F). In any case, soaking time shall never exceed 90 min after Ts reaches 1030°C (1885°F).
Quenching: shall be performed in oil or pressurized gas. Pressurized gas should be preferred when quenching complex shapes. Fast cooling has to be applied from austenitizing temperature down to 150°C (300°F). Cooling rate, measured at the surface of the cavity, must be at least 30°C/min (55°F/min) between austenitizing temperature and 530°C (990°F). To limit stresses, a special attention shall be paid at the temperature difference between surface and core. Especially in the temperature range 400/450°C (750/840°F), the temperature difference between surface and core shall not exceed 100°C (180°F). Below 150°C (300°F), cavity should be air cooled to 50/80°C and should then be immediately loaded in a furnace to perform a first tempering. Martempering bath is possible at 500-550°C to limit distortions.
Tempering: minimum of 2 tempering should be performed immediately after quenching. The tempering temperature should be held 2 hours minimum or 30mn per 25 mm of thickness (30min/inch). Avoid the brittle range of 430°C-550°C. Temper above 200°C. After tempering, pieces should be air cooled to room temperature.
PROPRIETARY 2343 - H11 Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY 2343 - H11 Materiais Equivalentes Internacionais
Exibindo 15 de 87 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 87 de equivalentes internacionais?
Veja todos as classes 87 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 87Referências Cruzadas
- 6Composição
- 2Propriedades Mecânicas
- 9Propriedades físicas
- 3Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 83Total de Fornecedores