PROPRIETARY N2711M Aços de ferramenta
Atualizações de dados
Este material conta com 33 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY N2711M Composição química
Villares Metals, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY N2711M Propriedades físicas
Temperatura
Este material conta com 33 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY N2711M Tratamento Térmico
- Annealing: Heat slowly and evenly to temperatures between 660 and 680°C, at a rate of 100°C/h, keeping 1 hour for every 25 mm of the largest section of the piece. Cool slowly in an oven (30°C/h) to 500°C, then cool in calm air.
Stress Relief: After machining with large material removal, stress relief is recommended, heating the molds slowly and evenly (100°C/h) up to 480/500°C, keeping half hour at temperature for every 25 mm of the highest section in the piece, regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Hardening: During hardening, the surface of the molds must be protected against decarburization and oxidation. Heat slowly and evenly at (100°C/h) to 400°C and then at a maximum of 300°C/h until the austenitizing temperature, between 890 and 910°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air to approximately 60°C.
Tempering: Temper immediately after quenching, as soon as the molds reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. The tempering temperature must be chosen according to the desired hardness.The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension.
PROPRIETARY N2711M Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY N2711M Materiais Equivalentes Internacionais
Exibindo 3 de 5 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 5 de equivalentes internacionais?
Veja todos as classes 5 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 5Referências Cruzadas
- 6Composição
- 2Propriedades Mecânicas
- 13Propriedades físicas
- 2Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 5Total de Fornecedores