PROPRIETARY N2711M Acciai per utensili
Aggiornamenti dei dati
Questo materiale dispone di 33 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca tutte le proprietà del materiale, inclusi i valori dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY N2711M Composizione chimica
Villares Metals, Product Data Sheets,
Cerchi dati completi sulle prestazioni dei materiali?
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY N2711M Proprietà fisiche
Temperatura
Questo materiale dispone di 33 dati sulle proprietà — qui ne viene mostrato solo un sottoinsieme.
Sblocca valori fisici dettagliati a diverse temperature e condizioni.
Registrazione gratuita richiesta • Accesso immediato
PROPRIETARY N2711M Trattamento Termico
- Annealing: Heat slowly and evenly to temperatures between 660 and 680°C, at a rate of 100°C/h, keeping 1 hour for every 25 mm of the largest section of the piece. Cool slowly in an oven (30°C/h) to 500°C, then cool in calm air.
Stress Relief: After machining with large material removal, stress relief is recommended, heating the molds slowly and evenly (100°C/h) up to 480/500°C, keeping half hour at temperature for every 25 mm of the highest section in the piece, regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Hardening: During hardening, the surface of the molds must be protected against decarburization and oxidation. Heat slowly and evenly at (100°C/h) to 400°C and then at a maximum of 300°C/h until the austenitizing temperature, between 890 and 910°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air to approximately 60°C.
Tempering: Temper immediately after quenching, as soon as the molds reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. The tempering temperature must be chosen according to the desired hardness.The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension.
PROPRIETARY N2711M Proprietà meccaniche
Temperatura
Hai bisogno di proprietà meccaniche complete per fare la scelta giusta?
Accedi ai dati completi su resistenza, durezza, fatica e altro ancora.
Registrazione gratuita richiesta • Accesso immediato
Materiali equivalenti internazionali di PROPRIETARY N2711M
Visualizzazione di 3 risultati su 5.
Le categorie di equivalenza si basano sul confronto della composizione chimica e delle proprietà meccaniche. Si raccomanda di verificare sempre l'idoneità del materiale rispetto alla specifica e all'applicazione prevista.
Hai bisogno dell'elenco completo dei 5 equivalenti internazionali?
Visualizza tutti i 5 gradi equivalenti con una mappatura dettagliata per norma, produttore e categoria di equivalenza.
Registrazione gratuita richiesta • Accesso immediato
Ottimizza la selezione dei materiali per la tua applicazione - Prenota una demo
- 5Riferimenti incrociati
- 6Composizione
- 2Proprietà meccaniche
- 13Proprietà fisiche
- 2Trattamento Termico
- -Metallografia
- -Lavorabilità
- -Sforzo-Deformazione
- -Formabilità
- -Fatica
- -Frattura
- -Strisciare
- -Giunzioni
- -Rivestimenti
- -Dimensioni
- -Tribologia
- -Corrosione
- -Invecchiamento
- -Resistenza agli agenti atmosferici
- -Irraggiamento
- 5Fornitori Totali