AA 6005A アルミニウム合金
材料グループ:
非鉄合金 / アルミニウム合金
国 / 規格:
米国 / AA
参考価格:
データ更新
最新情報: 2019-04
更新の総数: 3
更新履歴
2017-09
2016-02
この材料には 316 件の特性データがありますが、現在表示されているのは一部のみです。
登録して、温度や条件ごとの詳細データを含む全ての材料特性データにアクセスしましょう。
全ての材料データを見る ›
無料登録・すぐにアクセス
無料登録・すぐにアクセス
AA 6005A 化学組成
基準
値
単位
CAS 番号
基準
Al
値
剰余
単位
%
CAS 番号
7429-90-5
基準
Cr
値
≤ 0.30
単位
%
CAS 番号
7440-47-3
基準
Cu
値
≤ 0.30
単位
%
CAS 番号
7440-50-8
International alloy designations and chemical composition limits for wrought aluminum and wrought aluminum alloys - Teal Sheets (2025), 2025
材料の詳細な性能データをお探しですか？
全ての材料データを見る ›
無料登録・すぐにアクセス
無料登録・すぐにアクセス
AA 6005A 物理的性質
温度
熱膨張係数 (CTE)
登録して全ての詳細データを表示
無料アクセスで全データをご利用いただけます
全ての材料データを見る
この材料には 316 件の特性データがありますが、現在表示されているのは一部のみです。
温度や条件ごとの詳細な物理データを閲覧
全ての材料データを見る ›
無料登録・すぐにアクセス
無料登録・すぐにアクセス
AA 6005A 熱処理
- The times and temperatures are typical for various forms, sizes and methods of manufacture and may not exactly describe the optimum treatment for a specific item.
The nominal temperatures at which metal is heated (applies both for solution and precipitation heat treatment) should be attained as rapidly as possible and maintained ± 5°C of nominal during the time at temperature.
The time at precipitation heat treatment temperature will depend on time required for load to reach temperature. The times shown are based on rapid heating, with soaking time measured from the time the load reached within 5°C of the applicable temperature.
Material should be quenched from the solution heat-treating temperature as rapidly as possible and with minimum delay after removal from the furnace. Quenching is typically performed by immersion of wrought products in a cold water bath, although some forgings are quenched in hot-water. Quenching may be performed by alternative means such as total immersion in an aqueous polymer solution, liquefied gas, hot water, or boiling water, or by air blast or fog to minimize distortion provided samples from the material. The use of high-velocity high-volume jets of cold water is also effective for some materials.
For extruded rod, bar, profiles and tubes
Temper T1: Quenched directly from the extrusion press, naturally aged. Some extrusions may be adequately quenched using a room temperature air blast.
Temper T4: Solution heat treated at 510°C, quenched, naturally aged. By suitable control of extrusion temperature, product may be quenched directly from extrusion press to provide specified properties for this temper. Some products may be adequately quenched in air blast at room temperature. By definition, this temper designation is that which would apply after natural aging even though mechanical properties for this alloy-temper product have not been registered.
Temper T5: Quenched directly from the extrusion press, precipitation heat treated at 175° for 8 hours. Some extrusions may be adequately quenched using a room temperature air blast.
Temper T61: Solution heat treated at 510°C, quenched, precipitation heat treated at 175° for 8 hours. By suitable control of extrusion temperature, product may be quenched directly from extrusion press to provide specified properties for this temper. Some products may be adequately quenched in air blast at room temperature. By definition, this temper designation is that which would apply after natural aging even though mechanical properties for this alloy-temper product have not been registered.
Annealing (O)
Heated at 415°C, held for 2-3 hours. This treatment is intended to remove effects of solution heat treatment and include cooling at a rate of about 30°C per hour from the annealing temperature to 260°C. The rate of subsequent cooling is unimportant. Treatment at 345°C, followed by uncontrolled cooling, may be used to remove the effects of cold work, or to partially remove the effects of heat treatment. By definition, this temper designation is that which would apply after annealing even though mechanical properties for this alloy temper product have not been registered.
AA 6005A 機械的特性
温度
AA 6005A国際相当材
127件中15を表示しています。
材料
規格
国 / 製造業者
同等のカテゴリ
相当区分は、化学成分および機械的特性の比較に基づいています。実際の用途への適用にあたっては、必ず該当する規格要件に照らして適合性をご確認ください。
用途に最適な材料を選定 - デモを予約
- 127相互参照
- 24成分
- 30機械的特性
- 26物理的特性
- 1熱処理
- 1金属組織
- -被削性
- 10応力-ひずみ
- -成形性
- 2疲労
- -破壊
- -クリープ
- 4接合
- -コーティング
- -寸法
- -トライボロジ
- 1腐食
- -時効
- -耐候性
- -照射
- 90総仕入先数