PROPRIETARY VP420IM Aciers inoxydables
Mises à jour des données
Ce matériau a 433 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY VP420IM Composition chimique
Villares Metals, Product Data Sheets,
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
PROPRIETARY VP420IM Propriétés physiques
Température
Ce matériau a 433 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
PROPRIETARY VP420IM Traitement thermique
- Annealing: Soft annealing should be carried out by slow heating (100°C/h) to 780/840°C for 1 hour (after soaking), followed by slow cooling at 30°C per hour to 600°C and, then, by air cooling.
Stress relieving:The indicated procedure is slow heating (100°C/h) to ~ 650°C, holding until complete homogenisation (normally 30 min for 25 mm of the larger section, with minimum of 2 hours), and slow furnace cooling at least down to 100°C.
Hardening and Tempering: The recommended temperatures are: Pre-heating (400 - 450°C), Hardening (1000 - 1040°C) usually at 1025°C, Tempering (175 – 550°C). After preheating, moulds must be slow heated (300°C/h max.) to hardening temperature, holding 30 min after soaking (i. e. after mould is fully heated throughout). Use of protective atmosphere (or vacuum) is important during heating to hardening.
Quenching may be done in oil, holding until reaching 80°C. Then, it is recommended that moulds are carried to another furnace at 100/150°C in order to equalise temperature (in this step 1h for each 100 mm is required). Immediately after this treatment, heating to tempering should start. Double tempering is required and after each one moulds must cool down to room temperature. For each tempering treatments, the holding time of at least 2 h (after soaking) is necessary. As discussed before, tempering between 200 - 300°C is recommended to improve corrosion resistance.
PROPRIETARY VP420IM Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
PROPRIETARY VP420IM Matériaux équivalents internationaux
Affichage de 15 sur 226 résultats.
Les catégories d'équivalence reflètent une comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation par rapport à la spécification applicable à votre utilisation.
Besoin de la liste complète des 226 équivalents internationaux ?
Consultez les 226 nuances équivalentes avec une correspondance détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 226Références croisées
- 5Composition
- 1Propriétés mécaniques
- 5Propriétés physiques
- 2Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 194Fournisseurs totaux