UNI C 46 Aciers de construction
Mises à jour des données
Ce matériau a 380 entrées de propriétés – seul un aperçu est visible ici.
Déverrouillez l’accès aux propriétés détaillées du matériau, notamment en température et dans différentes conditions.
Inscription gratuite requise • Accès instantané
UNI C 46 Composition chimique
UNI 7065: 1972 / Produits en acier non allié finis plats laminés à froid. Bandes avec une teneur en carbone comprise entre 0,10 et 0,60%
Vous souhaitez voir toutes les données sur ce matériau ?
Inscription gratuite requise • Accès instantané
UNI C 46 Propriétés physiques
Température
Ce matériau a 380 entrées de propriétés – seul un aperçu est visible ici.
Déverrouiller l’accès aux propriétés physiques à différentes températures et conditions.
Inscription gratuite requise • Accès instantané
UNI C 46 Traitement thermique
- Material is normally supplied in the annealed or normalised condition. The values shown in the mechanical properties table apply to the following conditions: TC: Annealed. TD: Normalised. TF: Hardened and tempered. Spheroidised: Spheroidise annealed. Annealed: Annealed to obtain a structure with a controlled hardness. Heat treated: Normalised or hardened and tempered followed by surface hardening followed by stress relieving at 140 to 180°C for one hour (to achieve the minimum surface hardness value specified after flame or induction hardening followed by stress relieving). Anneal at 650 - 700°C. Normalise at 840 - 860°C. Harden from 820 - 860°C and temper at 550 - 660°C for at least 1 hour.
- Material is normally supplied in the hot rolled condition but, subject to agreement, may be supplied in one of the following conditions: Soft Annealed (SA) to a maximum hardness by annealing at 650 - 700°C. Spheroidise Annealed (Spheroidised). Annealed to obtain a ferritic/pearlite structure (Annealed). Normalized at 840 - 870°C. Hardened and Tempered (H+T). The H+T values shown in the mechanical properties table are obtained from a test piece hardened by water quenching from 820 - 840°C followed by tempering at 550 - 650°C for at least 1 hour. The temperature of the water must be between 15 - 30°C. The Rockwell C Scale hardness minimum value (Heat Treated condition) shown in the mechanical properties table is the surface hardness which must be obtained whether material is in the normalised condition and subsequently surface hardened or whether the material is in the hardened and tempered condition and subsequently surface hardened; Both treatments are followed by tempering at 140-180°C for approximately 1 hour.
UNI C 46 Propriétés mécaniques
Température
Vous avez besoin des propriétés mécaniques détaillées pour faire le bon choix ?
Accédez aux données complètes de résistance, dureté, fatigue et plus encore.
Inscription gratuite requise • Accès instantané
UNI C 46 Matériaux équivalents internationaux
Affichage de 15 résultats sur 208.
Les catégories d'équivalence reflètent la comparaison de la composition chimique et des propriétés mécaniques — vérifiez toujours l'adéquation avec la spécification applicable à votre application.
Besoin de la liste complète des 208 équivalents internationaux ?
Consultez les 208 nuances équivalentes avec une cartographie détaillée par norme, producteur et catégorie d'équivalence.
Inscription gratuite requise • Accès instantané
Optimisez les choix de matériaux pour votre application - Réserver une démo
- 208Références croisées
- 15Composition
- 27Propriétés mécaniques
- 3Propriétés physiques
- 6Traitement thermique
- -Métallographie
- -Usinabilité
- -Contrainte-Déformation
- -Formabilité
- -Fatigue
- -Rupture
- -Rampant
- -Assemblages
- -Revêtements
- -Dimensions
- -Tribologie
- -Corrosion
- -Vieillissement
- -Résistance aux intempéries
- -Irradiation
- 121Fournisseurs totaux