PROPRIETARY VP20TS Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 146 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20TS Propiedades físicas
Temperatura
Este material cuenta con 146 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20TS Tratamiento Térmico
- Annealing: Heat slowly and evenly to temperatures between 840 and 850°C, at a maximum rate of 100°C/h, keeping 1 hour for every 25 mm of the largest section of the piece. Slowly cool in an oven (30°C/h) to 500ºC; then cool in calm air.
Stress Relief: Heating the molds slowly and evenly (max. 100°C/h) up to about 530°C, keeping 0.5 hour in temperature for every 25 mm of the largest section in the piece; regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Hardening: During hardening, the surface of the molds must be protected against decarburization and oxidation. Heat slowly and uniformly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitization temperature, between 880 and 920°C. Allow 0.5 hours for each inch of thickness. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air between 50 and 70°C.
Tempering: Tempering immediately after quenching, as soon as the molds reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. The tempering temperature must be chosen according to the desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension.
Nitriding: It is indicated when greater wear resistance is desired. It presents good response to nitriding, reaching surface hardness of up to 800 HV.
PROPRIETARY VP20TS Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY VP20TS Materiales Internacionales Equivalentes
Mostrando 15 de 71 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 71 internacionales equivalentes?
Consulte los grados 71 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 71Referencias cruzadas
- -Composición
- 3Propiedades mecánicas
- 3Propiedades físicas
- 2Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 67Proveedores Totales