PROPRIETARY WM A-8 Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 60 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM A-8 Composición química
Ellwood Specialty Steel, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM A-8 Propiedades físicas
Temperatura
Este material cuenta con 60 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM A-8 Tratamiento Térmico
- Preheating: Heat at a rate not exceeding 400°F per hour to 1400-1450°F and equalize.
Austenitizing (high heat): Heat slowly from the preheat. Furnace or Salt: 1825-1850°F. Soak for 30 minutes for the first inch of thickness, plus 15 minutes for each additional inch.
Quenching: Air, pressurized gas, or interrupted oil to 150-125°F. Note: Sizes over 5 inches in cross section may not achieve full hardness by cooling in still air. It is usually necessary to increase the quench cooling rate between 1400 to 900°F by using an air blast, pressurized gas, or an interrupted oil quench. For the oil quench, quench until black, about 900°F, then cool in still air to 150-125°F.
Tempering: Temper immediately after quenching. Hold temperature for 1 hour per inch of thickness, 2 hours minimum, then air cool to ambient temperature. The typical tempering range is 300 to 600°F. Double tempering is recommended for tempering temperatures of 900°F and higher. To minimize internal stresses in cross sections greater than 6 inches and to improve stability in tools that will be EDM’d after heat treatment, a soaking time of 4 to 6 hours at the tempering temperature is strongly recommended. Cryogenic Treatment: Some prefer to do cryogenic treatment as an extension of the quench from the austenitizing treatment. Others prefer to cryogenically treat after tempering.
Annealing: Annealing must be performed after hot working and before rehardening. Heat at a rate not exceeding 400°F per hour to 1550°F, and hold at temperature for 1 hour per inch of maximum thickness; 2 hours minimum. Then cool slowly with the furnace at a rate not exceeding 50°F per hour to 1000°F Continue cooling to ambient temperature in the furnace or in air. The resultant hardness should be a maximum of 241 HBW.
PROPRIETARY WM A-8 Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY WM A-8 Materiales Internacionales Equivalentes
Mostrando 1 de 1 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 1 internacionales equivalentes?
Consulte los grados 1 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 1Referencias cruzadas
- 6Composición
- 42Propiedades mecánicas
- 7Propiedades físicas
- 2Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 2Proveedores Totales