PROPRIETARY Carpenter CTS 20HC Alloy Aceros inoxidables
Actualizaciones de datos
Este material cuenta con 587 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Carpenter CTS 20HC Alloy Composición química
Carpenter Technology Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Carpenter CTS 20HC Alloy Propiedades físicas
Temperatura
Este material cuenta con 587 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Carpenter CTS 20HC Alloy Tratamiento Térmico
- Annealing: Carpenter CTS 20HC alloy should be annealed in a neutral atmosphere. Heat uniformly to 1550/1650F (843/899C), then cool very slowly in the furnace until the furnace is black. The furnace then can be turned off and allowed to cool naturally. Fully annealed hardness is HRB 100 maximum. Intermediate or process annealing can be performed by heating uniformly to 1350F/1450F (732/788C) followed by furnace cooling or air cooling. Slightly higher hardness will result from the lower-temperature annealing process. Hardening: Preheat to 1400/1500F (760/816C) then increase temperature to 1850/1950F (1010/1066C), soak for 15 to 30 minutes, quench in warm oil or cool in air. Do not overheat. Tempering: Carpenter CTS 20HC alloy can be tempered over a range of temperatures from 300F (149C) to 800F (427C), soaked at least one hour then air cooled to room temperature. The specific tempering treatment chosen will depend upon a number of factors including the austenitizing temperature utilized, application of a refrigeration treatment and the desired combination of final hardness, toughness and corrosion resistance (see hardness table). To remove peak stresses yet retain peak hardness, temper at 300F (149C) to 350F (177C). Tempering at temperatures of 800F (427C) and higher will reduce toughness and corrosion resistance. Sub-Zero Cooling: After hardening, the alloy may be refrigerated at -100/-120F (-73/-84C) for at least one hour then warmed to room temperature prior to tempering to minimize retained austenite. Refrigeration is most effective when performed within two hours after the austenitizing treatment.
PROPRIETARY Carpenter CTS 20HC Alloy Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Carpenter CTS 20HC Alloy Materiales Internacionales Equivalentes
Mostrando 15 de 353 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 353 internacionales equivalentes?
Consulte los grados 353 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 353Referencias cruzadas
- 8Composición
- 4Propiedades mecánicas
- 4Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 217Proveedores Totales