PROPRIETARY Uddeholm Impax Supreme Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 33 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Impax Supreme Composición química
Uddeholms AB, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Impax Supreme Propiedades físicas
Temperatura
Este material cuenta con 33 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Impax Supreme Tratamiento Térmico
- Soft annealing: Protect the steel and heat through to 700°C (1300°F). Then cool in the furnace at 28°C (50°F) per hour to 600°C (1110°F), then freely in air;
Stress relieving: After rough machining the tool should be heated through to 550°C (1020°F), holding time 2 hours. Cool slowly to room temperature;
Hardening: (The steel should be fully soft annealed before hardening.) Preheating temperature: 500-600°C (930-1110°F). Austenitizing temperature: 850°C (1560°F). The steel should be heated through to the austenitizing temperature and held at temperature for 30 minutes. (The tool need to be protected against decarburization and oxidation during the hardening process.);
Quenching media: High speed gas/circulating atmosphere (Only suitable for small dimensions), Oil (60-80°C/140-175°F), Martempering bath 300°C (570°F) max. 4 minutes, then air. (Temper immediately tool reaches 50-70°C (120-160°F);
Tempering: The tempering temperature is according to the hardness required. Temper twice with intermediate cooling to room temperature. Lowest tempering temperature 180°C (360°F) for small inserts, but preferred minimum is 250°C (480°F). Holding time at temperature minimum 2 hours.
Nitriding and Nitrocarburizing: prior to nitriding material should be rough machined, stress tempered at 550°C (1020°F) and grinded. Gas nitriding at 525°C (977°F) for 20 h and depth of case 0.30 mm or 30 h and depth of case 0.35 mm. Ion nitriding at 480°C (896°F) for 24 h and depth of case 0.30 mm or 48 h and depth of case 0.40 mm. Nitrocarburizing at 570°C (1058°F) for 2 h and depth of case 0.10 mm.
PROPRIETARY Uddeholm Impax Supreme Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Impax Supreme Materiales Internacionales Equivalentes
Mostrando 2 de 2 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 2 internacionales equivalentes?
Consulte los grados 2 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 2Referencias cruzadas
- 6Composición
- 7Propiedades mecánicas
- 10Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 7Proveedores Totales