PROPRIETARY Uddeholm Vanadis 10 SuperClean Tool steels

Material group: Ferrous Alloys / Tool steels

Country / Standard: PROPRIETARY

Data updates

Latest Update: 2016-04

Total number of updates: 1

Update History

This material has 27 properties — only a subset is shown here.

Unlock full material properties, including detailed values across temperatures and conditions.

PROPRIETARY Uddeholm Vanadis 10 SuperClean Chemical Composition

CRITERIA

VALUE

UNIT

CAS NUMBER

CRITERIA

VALUE

2.9000

UNIT

CAS NUMBER

7440-44-0

CRITERIA

VALUE

8.0000

UNIT

CAS NUMBER

7440-47-3

CRITERIA

VALUE

0.5000

UNIT

CAS NUMBER

7439-96-5

CRITERIA

VALUE

val1

UNIT

CAS NUMBER

7439-98-7

CRITERIA

VALUE

val1

UNIT

CAS NUMBER

7440-21-3

CRITERIA

VALUE

val1

UNIT

CAS NUMBER

7440-62-2

Uddeholms AB, Product Data Sheets,

Looking for full material performance data?

PROPRIETARY Uddeholm Vanadis 10 SuperClean Physical Properties

Temperature

0 - 30°C 100 - 300°C ≥ 300°C

PROPERTY / VALUE

Modulus of Elasticity

190 — 220 GPa

Unlock full details

Density

val1 kg/dm³

Unlock full details

Heat Capacity

val1 J/(kg∙°C)

Unlock full details

Poisson Coefficient

val1

Unlock full details

This material has 27 properties — only a subset is shown here.

Unlock detailed physical values across temperatures and conditions.

PROPRIETARY Uddeholm Vanadis 10 SuperClean Heat Treatments

Soft annealing: Protect the steel and heat through to 900°C. Cool in the furnace at 10°C per hour to 750°C, then freely in air.
Stress relieving: After rough machining the tool should be heated through to 650°C, holding time 2 hr. Cool slowly to 500°C, then freely in air;
Hardening: Pre-heating temperature: 600-700°C, Austenitizing temperature: 1020-1100°C. Holding time: 30 minutes. (A holding time of less than 30 minutes will result in loss of hardness. The tool should be protected against decarburization and oxidation during hardening.);
Quenching media: Forced air/gas, Vacuum furnace (gas overpressure 2-5 bar), Martempering bath or fluidized bed at 500-550°C, Martempering bath or fluidized bed at 200-350°C whereby 350°C is preferred. (Temper the tool as soon as its temperature reaches 50-70°C; In order to obtain the optimum properties for the tool, the cooling rate should be as fast as is concomitant with acceptable distortion; Tools with sections > 50 mm should be quenched in forced air.
Quenching in still air will result in loss of hardness.);
Tempering: Choose the tempering temperature according to the hardness. Temper twice with intermediate cooling to room temperature. Lowest tempering temperature 180°C. Holding time at temperature minimum 2 hr. At a hardening temperature of 1100°C or higher it should be tempered at minimum 525°C in order to reduce the amount of retained austenite.

PROPRIETARY Uddeholm Vanadis 10 SuperClean Mechanical Properties

Temperature

0 - 30°C

PROPERTY / VALUE

Brinell Hardness (HB)

280 — 310

Unlock full details

Need complete mechanical properties to make the right choice?

Get complete data on strength, hardness, fatigue, and more.

Optimize material selection for your application - Book A Demo

Looking to compare materials and make better decisions?

Access reliable material data, compare options, and make better decisions faster.

With Total Materia, you can:

Compare materials based on real engineering data

Find equivalent materials across standards

Evaluate performance for your specific conditions

Check compliance with global regulations

See how this works for your specific application

Take a Guided Tour

-Cross References

6Composition
1Mechanical Properties
12Physical Properties
3Heat Treatment
-Metallography
-Machinability

-Stress-Strain
-Formability
-Fatigue
-Fracture
-Creep

-Joints
-Coatings
-Dimensions
-Tribology

-Corrosion
-Ageing
-Weatherability
-Irradiation

5Total Suppliers