ABS AB/A10 Yapısal ve konstrüksiyon çelikleri
Veri güncellemeleri
Bu malzemenin 32 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklıklar ve koşullar genelinde ayrıntılı değerler de dahil olmak üzere tam malzeme özelliklerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/A10 Kimyasal bileşim
Rules for Materials and Welding, Part 2; Chapter 3 Section 7; Materials for Machinery, Boilers, Pressure Vessels, and Piping; Steel Machinery Forgings, American Bureau of Shipping, 2021
Tam malzeme performans verilerini mi arıyorsunuz?
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/A10 Fiziksel özellikler
Sıcaklık
Bu malzemenin 32 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklık ve koşullar genelinde ayrıntılı fiziksel özellik değerlerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/A10 Isıl İşlem
- Forgings are to be normalized, quenched and tempered.
Cooling prior to heat treatment: After forging and before reheating for heat treatment, the forgings are allowed to cool in a manner to prevent injury and to accomplish transformation.
Annealing: The forgings are to be reheated to and held at the proper austenitizing temperature for a sufficient time to effect the desired transformation and then be allowed to cool slowly and evenly in the furnace until the temperature has fallen to about 455°C (850°F) or lower.
Normalizing: The forgings are to be reheated to and held at the proper temperature above the transformation range for a sufficient time to effect the desired transformation and then withdrawn from the furnace and allowed to cool in air.
Tempering: The forgings are to be reheated to and held at the proper temperature, which will be below the transformation range, but above 580°C (1075°F), and then to be cooled at a rate not exceeding 55°C (100°F)/h until temperature below 315°C (600°F) is reached.
Stress Relieving: Where heat treatment for mechanical properties is carried out before final machining, the forgings are to be stress relieved at a temperature not more than 55°C (100°F) below the previous tempering temperature, but in no case less than 550°C (1025°F). The cooling rate is not to exceed 55°C (100°F)/h until a temperature below 315°C (600°F) is reached. Stress relieving may be used to augment tempering, in order to make final adjustments to the mechanical properties. If the stress relief temperature is within 14°C (25°F) of the final tempering temperature or higher for quenched and tempered steel, mechanical tests are to be made to assure that these temperatures have not adversely affected the mechanical properties of the steel.
Retreatment: The manufacturer may re-heat treat the forging, but not more than three additional times.
ABS AB/A10 Mekanik özellikler
Sıcaklık
Doğru seçimi yapmak için eksiksiz mekanik özelliklere mi ihtiyacınız var?
Mukavemet, sertlik, yorulma ve daha fazlası hakkında eksiksiz verilere ulaşın.
Ücretsiz kayıt gereklidir • Anında erişim
ABS AB/A10 Uluslararası eşdeğer malzemeler
10 sonuçtan 4 tanesi gösteriliyor.
Eşdeğerlik kategorileri kimyasal bileşim ve mekanik özellik karşılaştırmasını yansıtır — uygulamanız için uygunluğu her zaman geçerli şartnameye göre doğrulayın.
10 uluslararası eşdeğerin tam listesine mi ihtiyacınız var?
Standart, üretici ve eşdeğerlik kategorisine göre ayrıntılı eşleştirme ile 10 eşdeğer kaliteyi görüntüleyin.
Ücretsiz kayıt gereklidir • Anında erişim
Uygulamanız için en uygun olan malzeme seçiminizi optimize edin - Demo Rezervasyonu Yapın
- 10Çapraz Referanslar
- 9Bileşim
- 9Mekanik Özellikler
- 3Fiziksel Özellikler
- 1Isıl İşlem
- -Metalografi
- -İşlenebilirlik
- -Gerilme-Gerinim
- -Şekillendirilebilirlik
- -Yorulma
- -Kırılma
- -Sürünmek
- -Bağlantılar
- -Kaplamalar
- -Boyutlar
- -Triboloji
- -Korozyon
- -Yaşlanma
- -Hava şartlarına dayanıklılık
- -Radyasyon etkisi
- -Toplam Tedarikçiler