PROPRIETARY Uddeholm Vidar 1 Aços de ferramenta
Atualizações de dados
Este material conta com 47 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Vidar 1 Composição química
Uddeholms AB, Product Data Sheets,
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Vidar 1 Propriedades físicas
Temperatura
Este material conta com 47 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Vidar 1 Tratamento Térmico
- Soft annealing:
Protect the steel and heat through to 850°C (1562°F). Then cool in furnace at 10°C (20°F) per hour to 650°C (1202°F), then freely in air.
Stress relieving:
After rough machining the tool should be heated through to 650°C (1202°F), holding time 2 hours. Cool slowly to 500°C (932°F), then freely in air.
Hardening:
Preheating temperature: 600–850°C (1112–1562°F) (normally two preheating steps). Austenitizing temperature: 990–1010°C (1814–1850°F), normally 990–1000°C (1814–1832°F). Soaking time: 30–45 minutes. Protect the tool against decarburization and oxidation during austenitizing.
Quenching media:
High speed gas/circulating atmosphere, vacuum (high speed gas with sufficient positive pressure), martempering bath (salt or fluidized bed) at 500–550°C (932–1022°F), martempering bath (salt or fluidized bed) at 180–220°C (356–428°F), warm oil. Temper the tool as soon as its temperature reaches 50–70°C (122–158°F). In order to obtain the optimum properties for the tool, the cooling rate should be fast, but not at a level that gives excessive distortion or cracks.
Tempering:
Temperature should be choosen according to the hardness required. Temper twice with intermediate cooling to room temperature. Lowest tempering temperature 180°C (356°F). Holding time at temperature minimum 2 hours. Tempering in the range of 425–550°C (797–1022°F) for the intended final hardness will result in a lower toughness.
Nitriding and nitrocarburizing:
Before nitriding, the tool should be hardened and tempered at a temperature at least 50°C (120°F) above the nitriding temperature. Gas nitriding at 510°C (950°F) for 10 h and depth of 0.12 mm or 30 h and depth of 0.20 mm. Plasma nitriding at 480°C (895°F) for 10 h and depth of 0.14 mm or 30 h and depth of 0.19 mm. Nitrocarburizing in gas at 580°C (1075°F) for 2.5 h and depth of 0.12 mm or in salth bath at 580°C (1075°F) for 1 h and depth of 0.07 mm.
PROPRIETARY Uddeholm Vidar 1 Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
PROPRIETARY Uddeholm Vidar 1 Materiais Equivalentes Internacionais
Exibindo 1 de 8 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas, sempre verifique a adequação do material em relação à especificação aplicável à sua aplicação.
Precisa da lista completa do 8 de equivalentes internacionais?
Veja todos as classes 8 equivalentes com mapeamento detalhado por norma, fabricante e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 8Referências Cruzadas
- 6Composição
- 22Propriedades Mecânicas
- 3Propriedades físicas
- 2Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- 2Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 4Total de Fornecedores