UNI C 48 Aços estruturais e de construcão
Atualizações de dados
Este material conta com 180 propriedades — apenas uma parte está sendo exibida aqui.
Desbloqueie todas as propriedades do material, incluindo valores detalhados em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
UNI C 48 Composição química
UNI 7847: 1979 / Produtos de aço especial ligados e não-ligados laminados a quente, tais como barras e bobinas, tratadas por endurecimento superficial Qualidades, requisitos e testes
Precisa de dados completos de desempenho de materiais?
Registro gratuito requerido • Acesso instantâneo
UNI C 48 Propriedades físicas
Temperatura
Este material conta com 180 propriedades — apenas uma parte está sendo exibida aqui.
Desbloquear valores físicos específicos em diferentes temperaturas e condições.
Registro gratuito requerido • Acesso instantâneo
UNI C 48 Tratamento Térmico
- Material is normally supplied in the annealed or normalised condition. The values shown in the mechanical properties table apply to the following conditions: TC: Annealed. TD: Normalised. TF: Hardened and tempered. Spheroidised: Spheroidise annealed. Annealed: Annealed to obtain a structure with a controlled hardness. Heat treated: Normalised or hardened and tempered followed by surface hardening followed by stress relieving at 140 to 180°C for one hour (to achieve the minimum surface hardness value specified after flame or induction hardening followed by stress relieving). Anneal at 650 - 700°C. Normalise at 830 - 850°C. Harden from 805 - 845°C and temper at 550 - 660°C for at least 1 hour.
- Material is normally supplied in the hot rolled condition but, subject to agreement, may be supplied in one of the following conditions: Soft Annealed (SA) to a maximum hardness by annealing at 650 - 700°C. Spheroidise Annealed (Spheroidised). Annealed to obtain a ferritic/pearlite structure (Annealed). Normalized at 840 - 870°C. Hardened and Tempered (H+T). The H+T values shown in the mechanical properties table are obtained from a test piece hardened by water or oil quenching from 820 - 850°C followed by tempering at 550 - 650°C for at least 1 hour. The temperature of the water must be between 15 - 30°C. The temperature of the oil must be between 15 - 60°C. The Rockwell C Scale hardness minimum value (Heat Treated condition) shown in the mechanical properties table is the surface hardness which must be obtained whether material is in the normalised condition and subsequently surface hardened or whether the material is in the hardened and tempered condition and subsequently surface hardened; Both treatments are followed by tempering at 140-180°C for approximately 1 hour.
UNI C 48 Propriedades mecânicas
Temperatura
Precisa de propriedades mecânicas completas para fazer a escolha certa?
Acesse dados detalhados de resistência, dureza, fadiga e muito mais.
Registro gratuito requerido • Acesso instantâneo
UNI C 48 Materiais equivalentes internacionais
Mostrando 15 de 80 resultados.
As categorias de equivalência refletem a comparação da composição química e das propriedades mecânicas — verifique sempre a adequação de acordo com a especificação aplicável à sua aplicação.
Precisa da lista completa de 80 equivalentes internacionais?
Veja todas as 80 classes equivalentes com mapeamento detalhado por norma, produtor e categoria de equivalência.
Registro gratuito requerido • Acesso instantâneo
Otimizar seleção de materiais para sua aplicação - Agende uma demonstração
- 80Referências Cruzadas
- 10Composição
- 22Propriedades Mecânicas
- 3Propriedades físicas
- 3Tratamento térmico
- -Metalografia
- -Usinabilidade
- -Tensão-Deformação
- -Conformabilidade
- -Fadiga
- -Fratura
- -Rastejante
- -Junta
- -Revestimentos
- -Dimensões
- -Tribologia
- -Corrosão
- -Envelhecimento
- -Resistência às Intempéries
- -Irradiação
- 62Total de Fornecedores