AA Alclad 2014 Stopy Aluminium
Aktualizacje danych
Ten materiał ma 332 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA Alclad 2014 Właściwości fizyczne
Temperatura
Ten materiał ma 332 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA Alclad 2014 Obróbka cieplna
- The times and temperatures are typical for various forms, sizes and methods of manufacture and may not exactly describe the optimum treatment for a specific item.
The nominal temperatures at which metal is heated (applies both for solution and precipitation heat treatment) should be attained as rapidly as possible and maintained ± 5°C of nominal during the time at temperature.
The time at precipitation heat treatment temperature will depend on time required for load to reach temperature. The times shown are based on rapid heating, with soaking time measured from the time the load reached within 5°C of the applicable temperature.
Material should be quenched from the solution heat-treating temperature as rapidly as possible and with minimum delay after removal from the furnace. Quenching is typically performed by immersion of wrought products in a cold water bath, although some forgings are quenched in hot-water. Quenching may be performed by alternative means such as total immersion in an aqueous polymer solution, liquefied gas, hot water, or boiling water, or by air blast or fog to minimize distortion provided samples from the material. The use of high-velocity high-volume jets of cold water is also effective for some materials.
For flat sheet
Temper T3: Solution heat treated at 500°C, quenched, naturally aged. Cold work subsequent to solution heat treatment is required to attain the specified mechanical properties for this temper.
Temper T42: Solution heat treated at 500°C, quenched, naturally aged.
Temper T62: Solution heat treated at 500°C, quenched, precipitation heat treated at 160°C for 18 hours.
For coiled sheet
Temper T4: Solution heat treated at 500°C, quenched, naturally aged.
Temper T42: Solution heat treated at 500°C, quenched, naturally aged.
Temper T6: Solution heat treated at 500°C, quenched, precipitation heat treated at 160°C for 18 hours.
Temper T62: Solution heat treated at 500°C, quenched, precipitation heat treated at 160°C for 18 hours.
For plate
Temper T451: Solution heat treated at 500°C, quenched, naturally aged. Stress-relieved by stretching is required to produce a specified amount of permanent set subsequent to solution heat treatment.
Temper T42: Solution heat treated at 500°C, quenched, naturally aged.
Temper T651: Solution heat treated at 500°C, quenched, precipitation heat treated at 160°C for 18 hours. Stress-relieved by stretching is required to produce a specified amount of permanent set prior to any precipitation heat treatment.
Temper T62: Solution heat treated at 500°C, quenched, precipitation heat treated at 160°C for 18 hours.
AA Alclad 2014 Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA Alclad 2014 Międzynarodowe materiały równoważne
Wyświetlanie 4 ze 4 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych - zawsze należy zweryfikować przydatność względem specyfikacji obowiązującej dla danego zastosowania.
Potrzebujesz pełną listę 4 międzynarodowych odpowiedników?
Zobacz pełną listę 4 równoważnych materiałów wraz ze szczegółowym przyporządkowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 4Odniesienia
- -Skład Chemiczny
- 95Właściwości Mechaniczne
- 15Właściwości Fizyczne
- 1Obróbka Cieplna
- -Metalografia
- -Obrabialność
- 67Naprężenie-Odkształcenie
- -Plastyczność
- 4Zmęczenie materiału
- -Pęknięcie
- -Pełzać
- 16Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- 1Korozja
- 126Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 3Łączna liczba dostawców