AA 6005 Stopy Aluminium
Aktualizacje danych
Ten materiał ma 218 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA 6005 Skład chemiczny
International alloy designations and chemical composition limits for wrought aluminum and wrought aluminum alloys - Teal Sheets (2025), 2025
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA 6005 Właściwości fizyczne
Temperatura
Ten materiał ma 218 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA 6005 Obróbka cieplna
- The times and temperatures are typical for various forms, sizes and methods of manufacture and may not exactly describe the optimum treatment for a specific item.
The nominal temperatures at which metal is heated (applies both for solution and precipitation heat treatment) should be attained as rapidly as possible and maintained ± 5°C of nominal during the time at temperature.
The time at precipitation heat treatment temperature will depend on time required for load to reach temperature. The times shown are based on rapid heating, with soaking time measured from the time the load reached within 5°C of the applicable temperature.
For extruded rod, bar, profiles and tubes
Temper T1: Quenched directly from the extrusion press, naturally aged. Some extrusions may be adequately quenched using a room temperature air blast.
Temper T5: Quenched directly from the extrusion press, precipitation heat treated at 175° for 8 hours. Some extrusions may be adequately quenched using a room temperature air blast.
Annealing (O)
Heated at 415°C, held for 2-3 hours. This treatment is intended to remove effects of solution heat treatment and include cooling at a rate of about 30°C per hour from the annealing temperature to 260°C. The rate of subsequent cooling is unimportant. Treatment at 345°C, followed by uncontrolled cooling, may be used to remove the effects of cold work, or to partially remove the effects of heat treatment. By definition, this temper designation is that which would apply after annealing even though mechanical properties for this alloy temper product have not been registered.
AA 6005 Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
AA 6005 Międzynarodowe materiały równoważne
Wyświetlanie 15 ze 68 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych - zawsze należy zweryfikować przydatność względem specyfikacji obowiązującej dla danego zastosowania.
Potrzebujesz pełną listę 68 międzynarodowych odpowiedników?
Zobacz pełną listę 68 równoważnych materiałów wraz ze szczegółowym przyporządkowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 68Odniesienia
- 22Skład Chemiczny
- 21Właściwości Mechaniczne
- 14Właściwości Fizyczne
- 1Obróbka Cieplna
- -Metalografia
- -Obrabialność
- 7Naprężenie-Odkształcenie
- -Plastyczność
- 1Zmęczenie materiału
- -Pęknięcie
- -Pełzać
- -Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- -Korozja
- 31Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 53Łączna liczba dostawców