Generic Nicrosilal Żeliwa
Aktualizacje danych
Ten materiał ma 4369 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Generic Nicrosilal Skład chemiczny
Nickel Institute website - Technical Literature,
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Generic Nicrosilal Właściwości fizyczne
Temperatura
Ten materiał ma 4369 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Generic Nicrosilal Obróbka cieplna
- Stress relieve: This is done by heating to 600-650°C (1110-1200°F) at a rate of 50-100°C/hour (90-180°F/hour). The castings should be held in this temperature range for 2hours plus 1 hour per 25 mm (1 inch) of section thickness. They should then be furnace-cooled to or near ambient temperature. With castings made from Ni-resist alloys with the higher coefficients of expansion and with thin sections it is most important to have controlled, uniform heating and slow cooling.
High temperature stability: Castings intended for static or cyclic service at 480°C (900°F) and above can be given a dimensional stabilization heat treatment. If not done, carbon is slowly removed from the austenite matrix while at service temperatures. This results in a small growth in volume and distortion can occur. When the heat treatment is used this problem is eliminated. The proper cycle is to heat to 850-900°C (1560-1650°F) at 50-100°C (90-180°F) per hour. The castings should be held in this temperature range for not less than 2 hours plus 1 hour for each 25 mm (1 inch) of section thickness followed by air cooling.
Normalizing: The same heat treatment that is used for high-temperature stabilization can be used for normalizing. It will result in an increase in yield strength and elongation.
Annealing: If the castings of the correct composition are higher in hardness than expected, excessive carbide formation has probably occurred. Some softening and improved machinability can be achieved through high temperature annealing. This heat treatment will breakdown and/or spheroidize some of the carbides. To anneal, castings should be heated to 950-1025°C (1740-1875°F) at 50-100°C (90-180°F) per hour. They should be held in this temperature range for 2 hours per 25 mm (1 inch) of section thickness followed by cooling in the furnace or in still air.
Ambient temperature stability: For assured dimensional stability for service at ambient temperatures, slow, uniform heating to 815-840°C (1500-1560°F) if suggested. Castings should be held in this temperature range for one hour per 25 mm (1 inch) of section thickness and uniformly cooled to at least 315°C (600°F). For stringent requirements, the uniform cooling can be continued to ambient temperature.
Generic Nicrosilal Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Generic Nicrosilal Międzynarodowe materiały równoważne
Wyświetlanie 1 z 4 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych — zawsze należy sprawdzić przydatność względem obowiązującej specyfikacji dla danego zastosowania.
Potrzebujesz pełnej listy 4 międzynarodowych odpowiedników?
Zobacz wszystkie 4 równoważne gatunki ze szczegółowym mapowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 4Odniesienia
- 5Skład Chemiczny
- 3Właściwości Mechaniczne
- 6Właściwości Fizyczne
- 1Obróbka Cieplna
- -Metalografia
- -Obrabialność
- -Naprężenie-Odkształcenie
- -Plastyczność
- -Zmęczenie materiału
- -Pęknięcie
- -Pełzać
- -Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- 4348Korozja
- -Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 2Łączna liczba dostawców