NMX B-180 Grade 1 Stale konstrukcyjne
Aktualizacje danych
Ten materiał ma 32 właściwości - tutaj pokazano tylko ich część.
Odblokuj pełne właściwości materiału, w tym szczegółowe wartości w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
NMX B-180 Grade 1 Skład chemiczny
NMX-B-180: 1991 / Rury stalowe bezszwowe i spawane do pracy w niskiej temperaturze
Szukasz pełnych danych o właściwościach materiałów?
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
NMX B-180 Grade 1 Właściwości fizyczne
Temperatura
Ten materiał ma 32 właściwości - tutaj pokazano tylko ich część.
Odblokuj dostęp do szczegółowych wartości fizycznych w różnych temperaturach i warunkach.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
NMX B-180 Grade 1 Obróbka cieplna
- Normalized and tempered: Heat to a uniform temperature of min. 816°C, cooled in air and subsequently reheating to a suitable tempering temperature. Only for seamless pipes, reheat and control the final temperature of process in a range of 845 C to 945°C and cooled in a controlled atmosphere furnace, followed by tempering Seamless pipe Grades 1, 6 and 10 may be heat treated by uniform heating to a temperature not less than 815°C followed by quenching in a liquid bath and subsequently reheating to a suitable tempering temperature, in rather than any of the other heat treatments described in the preceding paragraphs Quenched and tempered: Heated to a uniform temperature of 800°C ± 15°C, and maintaining this temperature for a min. of 2 minutes/in. of thickness or one hour per 25.4 mm thick (not less than 15 minutes) and quenching by immersion in circulating water. Reheat the tubes to reach a uniform temperature between 565°C and 605°C, maintaining this temperature for a time of 2 minutes /mm thick or one hour per 25.4 mm thick (not less than 15 minutes) and cooled in air or water at a rate not less than 165°C/h. Double normalized and tempered: Heated to a uniform temperature of 900°C ± 15°C, and maintain this temperature for a min. of 2 minutes/ in. of thickness, or one hour per 25.4 mm thick (not less than 15 minutes) and cooled in air. Heating again until the tubes reach a uniform temperature of 790°C ± 15°C, holding this temperature for a min. of 2 minutes/mm thick or one hour per 25.4 mm (not less than 15 minutes) and cooled in air. Finally reheated to a uniform temperature of 565°C to 605°C, and maintain this temperature for a min. of 2 minutes/mm thick, or one hour per 25.4 mm (not less than 15 minutes), and cooled in air or water at a speed not less than 165°C/h.
NMX B-180 Grade 1 Właściwości mechaniczne
Temperatura
Potrzebujesz kompletnych właściwości mechanicznych, aby dokonać właściwego wyboru?
Uzyskaj kompletne dane dotyczące wytrzymałości, twardości, zmęczenia i innych parametrów.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
NMX B-180 Grade 1 Międzynarodowe materiały równoważne
Wyświetlanie 4 z 11 wyników.
Kategorie równoważności odzwierciedlają porównanie składu chemicznego i właściwości mechanicznych — zawsze należy sprawdzić przydatność względem obowiązującej specyfikacji dla danego zastosowania.
Potrzebujesz pełnej listy 11 międzynarodowych odpowiedników?
Zobacz wszystkie 11 równoważne gatunki ze szczegółowym mapowaniem według normy, producenta i kategorii równoważności.
Wymagana bezpłatna rejestracja • Natychmiastowy dostęp
Zoptymalizuj dobór materiałów do swojego zastosowania - Umów się na prezentację
- 11Odniesienia
- 4Skład Chemiczny
- 12Właściwości Mechaniczne
- 3Właściwości Fizyczne
- 1Obróbka Cieplna
- -Metalografia
- -Obrabialność
- -Naprężenie-Odkształcenie
- -Plastyczność
- -Zmęczenie materiału
- -Pęknięcie
- -Pełzać
- -Złącza
- -Powłoki
- -Wymiary
- -Trybologia
- -Korozja
- -Starzenie
- -Odporność na warunki atmosferyczne
- -Napromieniowanie
- 1Łączna liczba dostawców