PROPRIETARY SIHARD S471 Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 32 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY SIHARD S471 Composición química
SIJ Metal Ravne, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY SIHARD S471 Propiedades físicas
Temperatura
Este material cuenta con 32 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY SIHARD S471 Tratamiento Térmico
- Annealing: Heat at a rate not exceeding 50°C/h to reach 820-860°C, and hold at that temperature for 1 h for every 25 mm of workpiece thickness, 2 h minimum. Then cool down slowly in furnace to 600°C at a rate not exceeding 20°C/h. Continue cooling to ambient temperature in furnace or in the air. The final hardness should be maximum 240 HB.
Hardening: To minimize distortion and stresses in large or complex tools use double preheat. Heat at a rate not exceeding 50°C/h to 620-680°C for equalization, and then continue heating to reach 820-840°C. For normal tools, use only the second temperature range as a single preheating treatment. Heat rapidly from the preheat. Furnace or salt bath at 1040-1080°C. Equalize and soak at austenitizing temperature for 30 minutes for pieces up to 25 mm in thickness, plus 15 minutes for each additional 25 mm of thickness. Quenching at 1040 to 1080°C / air, oil or inert gas. To increase hardness by 1-2 HRC and dimensional stability after quenching, sub-zero treatment may be used. Temper immediately after quenching (when material reaches temp. 90-70°C). At least two tempering treatments are recommended to achieve a uniform tempered microstructure. Slowly heat to reach tempering temperature. Holding time in the furnace: 1 h for every 25 mm of workpiece thickness, but 2 h minimum. This is followed by air cooling. Typical tempering temperatures are 150 to 550°C. If surface treatment is to be applied, tempering temperature has to be 20-30°C higher than the temperature at which steel is treated.
PROPRIETARY SIHARD S471 Materiales Internacionales Equivalentes
Mostrando 1 de 1 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 1 internacionales equivalentes?
Consulte los grados 1 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 1Referencias cruzadas
- 7Composición
- -Propiedades mecánicas
- 17Propiedades físicas
- 3Tratamiento térmico
- 1Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 3Proveedores Totales