PROPRIETARY CPM Rex T15(HS) Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 84 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM Rex T15(HS) Composición química
Crucible Industries LLC., Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM Rex T15(HS) Propiedades físicas
Temperatura
Este material cuenta con 84 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM Rex T15(HS) Tratamiento Térmico
- Forged: 1095-1150°C. Do not forge below 925°C. Slow cool after forged. Annealed: Heat to 870°C, hold 2 hours, slow cool no faster than 15°C per hour to 540°C, then furnace cool or cool in still air to room temperature. Stress relieved: Annealed parts: Heat to 595-705°C, hold 2 hours, then air cool or furnace cool. Hardened parts: Heat to 15°C below original tempered temperature, or 540°C minimum, hold 2 hours, then air cool or furnace cool. Straightened: Best done warm 200-430°C. Hardened: Pre-heat: 815-845°C, hold long enough to soak through. A second pre-heat at 1010-1040°C is recommended when vacuum hardened. Austenitize: 1165-1235° C. Quench: Salt, oil or atmosphere quench to below 595°C, equalize then air cool to hand warm, below 50°C. Temper: Triple temper at 540°C or higher. Hold at least 2 hours at temperature for each temper.
- Annealing:
Heat to 870°C (1600°F), hold 2 hours, slow cool no faster than 15°C (25°F) per hour to 540°C (1000°F), then furnace cool or cool in still air to room temperature.
Stress Relieving
Annealed parts: Heat to 595–705°C (1100–1300°F), hold 2 hours, then air cool or furnace cool.
Hardened parts: Heat to 15°C (25°F) below original tempering temperature, or 540°C (1000°F) minimum, hold 2 hours, then air cool or furnace cool.
Straightening: Best done warm 200–430°C (400–800°F)
Hardening (Salt Bath or Vacuum Furnace preferred) Pre-heat: 815–845°C (1500–1550°F), hold long enough to soak through. A second pre-heat at 1010–1040°C (1850–1900°F) is recommended when vacuum hardening.
Austenitize: 1165–1235°C (2125–2250°F). To achieve HRC 66–68, 1220–1235°C (2225–2250°F) is recommended.
Quench: Salt, oil, or atmosphere quench to below 595°C (1100°F), equalize, then air cool to hand warm, below 50°C (125°F). Vacuum or atmosphere quenching may result in slightly lower hardness for larger tools. A fast quench rate from hardening temperature to below 595°C (1100°F) is critical to achieve optimum heat treat response. To minimize distortion, a slower cooling rate below 540°C (1000°F) may be used.
Temper: Triple temper at 540°C (1000°F) or higher. Hold at least 2 hours at temperature for each temper. Air cool to room temperature between tempers.
PROPRIETARY CPM Rex T15(HS) Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY CPM Rex T15(HS) Materiales equivalentes internacionales
Mostrando 1 de 2 resultados.
Las categorías de equivalencia reflejan la comparación de composición química y propiedades mecánicas — verifique siempre la idoneidad según la especificación aplicable a su aplicación.
¿Necesita la lista completa de 2 equivalentes internacionales?
Consulte los 2 grados equivalentes con mapeo detallado por norma, productor y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 2Referencias cruzadas
- 12Composición
- 56Propiedades mecánicas
- 8Propiedades físicas
- 2Tratamiento térmico
- 1Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 3Proveedores Totales