PROPRIETARY Trinamet Aceros inoxidables
Actualizaciones de datos
Este material cuenta con 69 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Trinamet Composición química
Carpenter Technology Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Trinamet Propiedades físicas
Temperatura
Este material cuenta con 69 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Trinamet Tratamiento Térmico
- Annealing: Heat uniformly to 732–788°C (1350–1450°F) for two to four hours on heat, remove from furnace and cool to room temperature. The hardness will be approximately Rockwell B 95 or equivalent. For lowest hardness, Rockwell B 88–93, heat to 880°C (1615°F) for one to two hours on heat, cool in the furnace at a rate not exceeding 28°C (50°F) per hour to 650°C (1200°F), and then remove from the furnace and air cool to room temperature.
Hardening: Trinamet stainless readily lends itself to heat treating in both batch and continuous types of heat treating furnaces. For the maximum attainable hardness of Rockwell C 49–52, the alloy should be heated to 1040–1065°C (1900–1950°F) and rapidly cooled to room temperature by quenching in oil or by forced air or gas cooling. Fifteen minutes on heat at 1040–1065°C (1900–1950°F) is generally adequate for screws, clips, pins, wire, and other small parts. A longer time (up to a maximum of about one hour) is required for larger sections. When heat treating in a protective atmosphere, nitrogen or argon with a dew point no higher than –40°C (–40°F) is suggested. Dissociated ammonia is considered unsuitable because of the risk of nitriding the work and the resulting reduction in corrosion resistance.
Tempering: After hardening, parts should be tempered for one to two hours at 177–204°C (350–400°F). When less than maximum hardness is required, parts may be tempered up to 316°C (600°F).
PROPRIETARY Trinamet Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Trinamet Materiales Internacionales Equivalentes
Mostrando 2 de 3 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 3 internacionales equivalentes?
Consulte los grados 3 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 3Referencias cruzadas
- 9Composición
- 44Propiedades mecánicas
- 11Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 1Proveedores Totales