PROPRIETARY Uddeholm Sleipner Aceros para herramientas
Actualizaciones de datos
Este material cuenta con 32 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Sleipner Composición química
Uddeholms AB, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Sleipner Propiedades físicas
Temperatura
Este material cuenta con 32 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Sleipner Tratamiento Térmico
- Soft annealing: Protect the steel and heat through to 850°C (1560°F). Then cool in the furnace at 11°C (20°F) per hour to 650°C (1200°F), then freely in air;
Stress relieving: After rough machining the tool should be heated through to 650°C (1200°F) and held for 2 hours. Cool slowly to 500°C (930°F) then freely in air;
Hardening: Preheating temperature: 600-650°C (1110-1200°F) and 850-900°C (1560-1650°F); Austenitizing temperature: 950-1080°C (1740-1980°F) but usually 1030-1050°C (1890-1920°F). Holding time: 30 minutes. (A holding time of less than recomended time will result in loss of hardness.) Protect the part against decarburization and oxidation during hardening;
Quenching media: Vacuum (high speed gas with sufficient overpressure minimum 2 bar); Martempering bath or fluidized bed at approx. 200–550°C (390-1020°F); Forced air/gas (Temper the tool as soon as its temperature reaches 50-70°C (120-160°F). In order to obtain the optimum properties for the tool, the cooling rate should be as fast as possible with regards to acceptable distortion. Martempering should be followed by forced air cooling if wall thickness is exceeding 50 mm;
Tempering: Choose the tempering temperature according to the hardness. Temper at least twice with intermediate cooling to room temperature. For highest dimensional stability and ductility, a minimum temperature of 540°C (1000°F) and three tempers is strongly recommended. Tempering at a lower temperature than 540°C (1000°F) may increase the hardness and compressive strength to some extent but also impair cracking resistance and dimensional stability. However, if lowering the tempering temperature, do not temper below 520°C (970°F). When tempering twice the minimum holding time at temperature is 2 hours. When tempering three times the minimum holding time is 1 hour. - Austenitizing temperature 1030°C (1890°F). Holding time 30 min.
PROPRIETARY Uddeholm Sleipner Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY Uddeholm Sleipner Materiales Internacionales Equivalentes
Mostrando 1 de 1 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 1 internacionales equivalentes?
Consulte los grados 1 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 1Referencias cruzadas
- 6Composición
- 1Propiedades mecánicas
- 14Propiedades físicas
- 3Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- 1Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 6Proveedores Totales