PROPRIETARY LESCALLOY BG42 VIM-VAR Aceros inoxidables
Actualizaciones de datos
Este material cuenta con 47 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY LESCALLOY BG42 VIM-VAR Composición química
Timken Steel Corporation, Product Data Sheets,
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY LESCALLOY BG42 VIM-VAR Propiedades físicas
Temperatura
Este material cuenta con 47 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY LESCALLOY BG42 VIM-VAR Tratamiento Térmico
- Hardening: Preheating: Heat to 816-843°C (1500-1550°F) and equalize.
Austenitizing (High Heat): Heat rapidly from the preheat, and soak for 10 to 15 minutes. Furnace or Salt: Typically: 1121°C (2050°F). For under hardening, use 1066-1080°C (1950-1975°F).
Quenching: Pressurized gas, warm oil, or salt. For pressurized gas, the furnace should have a minimum quench pressure of 4 bars. A quench rate of approximately 222°C (400°F) per minute to below 538°C (1000°F) is critical to obtain the desired properties. For oil, quench until black, about 482°C (900°F), then cool in still air to 66-51°C (150-125°F). For salt maintained at 538-593°C (1000-1100°F), equalize in the salt, then cool in still air to 66-51°C (150-125°F).
Cryogenic Treatment: An optional cryogenic treatment may be used immediately after quenching to 66-51°C (150 to 125°F). Cool to -73°C (-100°F), remove from cooling medium, and allow part to warm to ambient temperature in still air.
Tempering: Temper immediately after quenching or cryogenic treatment. The typical temperature range for knife blades is 510-566°C (950-1050°F). Tempering below 510°C (950°F) is not recommended. Hold at temperature for 2 hours then air cool to ambient temperature. Double tempering is required.
ANNEALING: Annealing must be performed after hot working (forging) and before rehardening. Heat at a rate not exceeding 222°C per hour (400°F per hour) to 885-899°C (1625-1650°F), and hold at temperature for 5 hours. Then cool slowly with the furnace at a rate not exceeding 28°C per hour (50°F per hour) to 427°C (800°F). Continue cooling to ambient temperature in the furnace or in air.
PROPRIETARY LESCALLOY BG42 VIM-VAR Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
PROPRIETARY LESCALLOY BG42 VIM-VAR Materiales Internacionales Equivalentes
Mostrando 1 de 3 resultados.
Las categorías de equivalencia reflejan comparaciones de composición química y propiedades mecánicas; siempre verifique la idoneidad del material según la especificación aplicable a su aplicación.
¿Necesita la lista completa de los 3 internacionales equivalentes?
Consulte los grados 3 equivalentes con el detalle completo de correspondencias por norma, fabricante y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 3Referencias cruzadas
- 16Composición
- 5Propiedades mecánicas
- 19Propiedades físicas
- 1Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 3Proveedores Totales