UNI C 53 Aceros estructurales y de construcción
Actualizaciones de datos
Este material cuenta con 125 propiedades — aquí solo se muestra una parte.
Accede a todas las propiedades del material, incluyendo valores detallados según temperatura y condiciones.
Se requiere registro gratuito • Acceso inmediato
UNI C 53 Composición química
UNI 7847: 1979 / Bobinas, barras y productos de acero especial, laminado en caliente, no aleados y aleados, para endurecimiento superficial. Cualidades, requisitos y pruebas
¿Buscas datos completos de desempeño de materiales?
Se requiere registro gratuito • Acceso inmediato
UNI C 53 Propiedades físicas
Temperatura
Este material cuenta con 125 propiedades — aquí solo se muestra una parte.
Consulta propiedades físicas detalladas en distintas temperaturas y condiciones.
Se requiere registro gratuito • Acceso inmediato
UNI C 53 Tratamiento Térmico
- Material is normally supplied in the annealed or normalised condition. The values shown in the mechanical properties table apply to the following conditions: TC: Annealed. TD: Normalised. TF: Hardened and tempered. Spheroidised: Spheroidise annealed. Heat treated: Normalised or hardened and tempered followed by surface hardening followed by stress relieving at 140 to 180°C for one hour (to achieve the minimum surface hardness value specified after flame or induction hardening followed by stress relieving). Anneal at 650 - 700°C. Normalise at 830 - 850°C. Harden from 805 - 845°C and temper at 550 - 660°C for at least 1 hour.
- Soft Annealed (SA) to a maximum hardness by annealing at 650 - 700°C. Spheroidise Annealed (Spheroidised). Annealed to obtain a ferritic/pearlite structure (Annealed). Normalized at 830 - 860°C. Hardened and Tempered (H+T). The H+T values shown in the mechanical properties table are obtained from a test piece hardened by water or oil quenching from 820 - 850°C followed by tempering at 550 - 650°C for at least 1 hour. The temperature of the water must be between 15 - 30°C. The temperature of the oil must be between 15 - 60°C. The Rockwell C Scale hardness minimum value (Heat Treated condition) shown in the mechanical properties table is the surface hardness which must be obtained whether material is in the normalised condition and subsequently surface hardened or whether the material is in the hardened and tempered condition and subsequently surface hardened; Both treatments are followed by tempering at 140-180°C for approximately 1 hour.
UNI C 53 Propiedades mecánicas
Temperatura
¿Buscas información completa sobre propiedades mecánicas para tomar la mejor decisión?
Obtén información completa sobre resistencia, dureza, fatiga y más.
Se requiere registro gratuito • Acceso inmediato
UNI C 53 Materiales equivalentes internacionales
Mostrando 15 de 60 resultados.
Las categorías de equivalencia reflejan la comparación de composición química y propiedades mecánicas — verifique siempre la idoneidad según la especificación aplicable a su aplicación.
¿Necesita la lista completa de 60 equivalentes internacionales?
Consulte los 60 grados equivalentes con mapeo detallado por norma, productor y categoría de equivalencia.
Se requiere registro gratuito • Acceso inmediato
Optimiza la selección de materiales para tu aplicación - Reservar una demo
- 60Referencias cruzadas
- 10Composición
- 20Propiedades mecánicas
- 3Propiedades físicas
- 4Tratamiento térmico
- -Metalografía
- -Maquinabilidad
- -Esfuerzo-Deformación
- -Conformabilidad
- -Fatiga
- -Fractura
- -Bicho raro
- -Uniones
- -Revestimientos
- -Dimensiones
- -Tribología
- -Corrosión
- -Envejecimiento
- -Resistencia a la intemperie
- -Irradiación
- 28Proveedores Totales