ASME
Standard · United States · 342 references
| Standard number | Materials | |
|---|---|---|
| SA/563M SA/563M (Carbon and Alloy Steel Nuts) | 14 | chevron_right |
| SA/AS 1548 SA/AS 1548 (Fine grained, weldable steel plates for pressure equipment) | 44 | chevron_right |
| SA/CSA-G40.21 SA/CSA-G40.21 (Specification for Structural Quality Steels) | 58 | chevron_right |
| SA/EN 10025-2 SA/EN 10025-2 (Specification for Hot Rolled Products of Structural Steels Part 2: Technical Delivery Conditions for Non-Alloy Structural Steels) | 58 | chevron_right |
| SA/EN 10028-2 SA/EN 10028-2 (Specification for flat products made of steels for pressure purposes - Part 2: Non-Alloy and Alloy Steels With Specified Elevated Temperature Properties) | 33 | chevron_right |
| SA/EN 10028-3 SA/EN 10028-3 (Specification for flat products made of steels for pressure purposes - Part 3: Weldable Fine Grain Steels, Normalized) | 28 | chevron_right |
| SA/EN 10028-4 SA/EN 10028-4 (Specification for flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties) | 14 | chevron_right |
| SA/EN 10028-7 SA/EN 10028-7 (Specification for flat products made of steels for pressure purposes - Part 7: Stainless steels) | 128 | chevron_right |
| SA/EN 10088-2 SA/EN 10088-2 (Specification for Stainless Steels Part 2: Technical Delivery Conditions for Sheet/Plate and Strip of Corrosion Resisting Steels for General Purposes) | 197 | chevron_right |
| SA/EN 10088-3 SA/EN 10088-3 (Specification for Stainless Steel Part 3: Technical Delivery Conditions for Semi-Finished Products, Bars, Rods, Wire, Sections, and Bright Products of Corrosion Resisting Steels for General Purposes) | 224 | chevron_right |
| SA/EN 10216-2 SA/EN 10216-2 (Specification for Seamless Steel Tubes for Pressure Purposes Part 2: Technical Delivery Conditions for Non-Alloy and Alloy Steel Tubes With Specified Elevated Temperature Properties) | 50 | chevron_right |
| SA/EN 10217-1 SA/EN 10217-1 (Specification for Welded Steel Tubes for Pressure Purposes Part 1: Technical Delivery Conditions for Electric Welded and Submerged Arc Welded Non-Alloy Steel Tubes With Specified Room Temperature Properties) | 12 | chevron_right |
| SA/EN 10222-2 SA/EN 10222-2 (Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperature properties) | 34 | chevron_right |
| SA/GB 6654 SA/GB 6654 (Specification for Steel Plates for Pressure Vessels) | 7 | chevron_right |
| SA/GB 713 SA/GB 713 (Specification for Steel Plates for Boilers and Pressure Vessels) | 12 | chevron_right |
| SA/IS 2062 SA/IS 2062 (Specification for Hot rolled Medium and High Tensile Structural Steel) | 38 | chevron_right |
| SA/ISO 898-1 SA/ISO 898-1 (Specification for fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread) | 9 | chevron_right |
| SA/JIS G3118 SA/JIS G3118 (Specification for carbon steel plates for pressure vessels for intermediate and moderate temperature services) | 6 | chevron_right |
| SA/JIS G4303 SA/JIS G4303 (Specification for stainless steel bars) | 63 | chevron_right |
| SA/JIS G5504 SA/JIS G5504 (Specification for Heavy-Walled Ferritic Spheroidal Graphite Iron Castings for Low Temperature Service) | 1 | chevron_right |
| SA/NF A 36-215 SA/NF A 36-215 (Specification for weldable fine grain steels for the transportation of dangerous substances) | 10 | chevron_right |
| SA-1008/SA-1008M SA-1008/SA-1008M (Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable) | 54 | chevron_right |
| SA-1010/SA-1010M SA-1010/SA-1010M (Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip) | 4 | chevron_right |
| SA-1011/SA-1011M SA-1011/SA-1011M (Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy With Improved Formability, and Ultra-High Strength) | 73 | chevron_right |
| SA-1017/SA-1017M SA-1017/SA-1017M (Specification for Pressure Vessel Plates, Alloy-Steel Chromium-Molybdenum-Tungsten) | 4 | chevron_right |
| SA-105/SA-105M SA-105/SA-105M (Carbon Steel Forgings for Piping Applications) | 1 | chevron_right |
| SA-106/SA-106M SA-106/SA-106M (Specification for Seamless Carbon Steel Pipe for High-Temperature Service) | 3 | chevron_right |
| SA-1091/SA-1091M SA-1091/SA-1091M (Standard Specification for Steel Castings, Creep-Strength Enhanced Ferritic Alloy, for Pressure-Containing Parts, Suitable for High Temperature Service) | 2 | chevron_right |
| SA-135/SA-135M SA-135/SA-135M (Specification for Electric-Resistance-Welded Steel Pipe) | 2 | chevron_right |
| SA-178/SA-178M SA-178/SA-178M (Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater Tubes) | 3 | chevron_right |
| SA-179/SA-179M SA-179/SA-179M (Seamless Cold-Drawn Low-Carbon Steel Heat Exchanger and Condenser Tubes) | 1 | chevron_right |
| SA-181/SA-181M SA-181/SA-181M (Carbon Steel Forgings, for General-Purpose Piping) | 2 | chevron_right |
| SA-182/SA-182M SA-182/SA-182M (Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service) | 109 | chevron_right |
| SA-192/SA-192M SA-192/SA-192M (Seamless Carbon Steel Boiler Tubes for High-Pressure Service) | 1 | chevron_right |
| SA-193/SA-193M SA-193/SA-193M (Specification for Alloy Steel and Stainless Steel Bolting Materials for High-Temperature Service) | 60 | chevron_right |
| SA-194/SA-194M SA-194/SA-194M (Specification for Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-Temperature Service, or Both) | 51 | chevron_right |
| SA-199 SA-199 (Seamless Cold-Drawn Intermediate Alloy-Steel Heat-Exchanger and Condenser Tubes) | 9 | chevron_right |
| SA-202/SA-202M SA-202/SA-202M (Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-Silicon) | 2 | chevron_right |
| SA-203/SA-203M SA-203/SA-203M (Specification for Pressure Vessel Plates, Alloy Steel, Nickel) | 5 | chevron_right |
| SA-204/SA-204M SA-204/SA-204M (Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum) | 3 | chevron_right |
| SA-209/SA-209M SA-209/SA-209M (Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes) | 3 | chevron_right |
| SA-210/SA-210M SA-210/SA-210M (Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes) | 2 | chevron_right |
| SA-213/SA-213M SA-213/SA-213M (Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes) | 103 | chevron_right |
| SA-214/SA-214M SA-214/SA-214M (Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes) | 1 | chevron_right |
| SA-216/SA-216M SA-216/SA-216M (Specification for Steel Castings, Carbon, Suitable for Fusion Welding for High-Temperature Service) | 3 | chevron_right |
| SA-217/SA-217M SA-217/SA-217M (Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts Suitable for High-Temperature Service) | 10 | chevron_right |
| SA-225/SA-225M SA-225/SA-225M (Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel) | 2 | chevron_right |
| SA-226/SA-226M SA-226/SA-226M (Electric-Resistance-Welded Carbon Steel Boiler Superheater Tubes for High-Pressure Service) | 1 | chevron_right |
| SA-231/SA-231M SA-231/SA-231M (Specification for Chromium-Vanadium Alloy Steel Spring Wire) | 1 | chevron_right |
| SA-232/SA-232M SA-232/SA-232M (Chromium-Vanadium Alloy Steel Valve Spring Quality Wire) | 1 | chevron_right |
| SA-234/SA-234M SA-234/SA-234M (Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High-Temperature Service) | 21 | chevron_right |
| SA-240/SA-240M SA-240/SA-240M (Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications) | 251 | chevron_right |
| SA-249/SA-249M SA-249/SA-249M (Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes) | 70 | chevron_right |
| SA-250/SA-250M SA-250/SA-250M (Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes) | 7 | chevron_right |
| SA-263 SA-263 (Stainless Chromium Steel-Clad Plate) | 1 | chevron_right |
| SA-264 SA-264 (Stainless Chromium-Nickel Steel-Clad Plate) | 1 | chevron_right |
| SA-265 SA-265 (Nickel and Nickel-Base Alloy-Clad Steel Plate) | 1 | chevron_right |
| SA-266/SA-266M SA-266/SA-266M (Carbon Steel Forgings, for Pressure Vessel Components) | 8 | chevron_right |
| SA-268/SA-268M SA-268/SA-268M (Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service) | 47 | chevron_right |
| SA-276/SA-276M SA-276/SA-276M (Specification for Stainless Steel Bars and Shapes) | 95 | chevron_right |
| SA-278/SA-278M SA-278/SA-278M (Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650°F (350°C)) | 20 | chevron_right |
| SA-283/SA-283M SA-283/SA-283M (Specification for Low and Intermediate Tensile Strength Carbon Steel Plates) | 4 | chevron_right |
| SA-285/SA-285M SA-285/SA-285M (Specification for Pressure Vessel Plates, Carbon Steel, Low-and Intermediate-Tensile Strength) | 3 | chevron_right |
| SA-29/SA-29M SA-29/SA-29M (General requirements for Steel Bars, Carbon and Alloy, Hot-Wrought) | 350 | chevron_right |
| SA-299/SA-299M SA-299/SA-299M (Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon) | 2 | chevron_right |
| SA-302/SA-302M SA-302/SA-302M (Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel) | 4 | chevron_right |
| SA-307 SA-307 (Specification for Carbon Steel Bolts and Studs, 60 000 psi Tensile Strength) | 3 | chevron_right |
| SA-31 SA-31 (Steel Rivets and Bars for Rivets, Pressure Vessels) | 2 | chevron_right |
| SA-311/SA-311M SA-311/SA-311M (Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements) | 28 | chevron_right |
| SA-312/SA-312M SA-312/SA-312M (Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes) | 79 | chevron_right |
| SA-320/SA-320M SA-320/SA-320M (Specification for Alloy Steel and Stainless steel Bolting for Low-Temperature Service) | 36 | chevron_right |
| SA-325 SA-325 (Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength) | 11 | chevron_right |
| SA-333/SA-333M SA-333/SA-333M (Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness) | 9 | chevron_right |
| SA-334/SA-334M SA-334/SA-334M (Specification for seamless and welded carbon and alloy steel tubes for low-temperature service) | 7 | chevron_right |
| SA-335/SA-335M SA-335/SA-335M (Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service) | 24 | chevron_right |
| SA-336/SA-336M SA-336/SA-336M (Specification for Alloy Steel Forgings for Pressure and High-Temperature Parts) | 21 | chevron_right |
| SA-350/SA-350M SA-350/SA-350M (Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components) | 13 | chevron_right |
| SA-351/SA-351M SA-351/SA-351M (Castings, Austenitic, for Pressure-Containing Parts) | 35 | chevron_right |
| SA-352/SA-352M SA-352/SA-352M (Steel Castings, Ferritic and Martensitic, for Pressure Containing Parts, Suitable for Low Temperature Service) | 10 | chevron_right |
| SA-353/SA-353M SA-353/SA-353M (Specification for Pressure Vessel Plates, Alloy Steel, Double-Normalized and Tempered 9% Nickel) | 1 | chevron_right |
| SA-354 SA-354 (Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners) | 2 | chevron_right |
| SA-358/SA-358M SA-358/SA-358M (Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications) | 78 | chevron_right |
| SA-36/SA-36M SA-36/SA-36M (Carbon Structural Steel) | 1 | chevron_right |
| SA-369/SA-369M SA-369/SA-369M (Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service) | 15 | chevron_right |
| SA-372/SA-372M SA-372/SA-372M (Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels) | 60 | chevron_right |
| SA-376/SA-376M SA-376/SA-376M (Seamless Austenitic Steel Pipe for High-Temperature Central-Station Service) | 20 | chevron_right |
| SA-387/SA-387M SA-387/SA-387M (Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum) | 18 | chevron_right |
| SA-395/SA-395M SA-395/SA-395M (Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures) | 2 | chevron_right |
| SA-401/SA-401M SA-401/SA-401M (Standard Specification for Steel Wire, Chromium-Silicon Alloy) | 1 | chevron_right |
| SA-403/SA-403M SA-403/SA-403M (Specification for Wrought Austenitic Stainless Steel Piping Fittings) | 85 | chevron_right |
| SA-409/SA-409M SA-409/SA-409M (Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature Service) | 24 | chevron_right |
| SA-412 SA-412 (Stainless and Heat-Resisting Chromium-Nickel-Manganese Steel Plate, Sheet, and Strip) | 7 | chevron_right |
| SA-414/SA-414M SA-414/SA-414M (Specification for steel, sheet, carbon, and high-strength, low alloy for pressure vessels) | 8 | chevron_right |
| SA-420/SA-420M SA-420/SA-420M (Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service) | 4 | chevron_right |
| SA-423/SA-423M SA-423/SA-423M (Seamless and Electric-Welded Low-Alloy Steel Tubes) | 3 | chevron_right |
| SA-426/SA-426M SA-426/SA-426M (Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service) | 13 | chevron_right |
| SA-430/SA-430M SA-430/SA-430M (Austenitic Steel Forged and Bored Pipe for High-Temperature Service) | 11 | chevron_right |
| SA-437/SA-437M SA-437/SA-437M (Specification for stainless and alloy-steel turbine-type bolting specially heat treated for high-temperature service) | 3 | chevron_right |
| SA-439/SA-439M SA-439/SA-439M (Specification for Austenitic Ductile Iron Castings) | 10 | chevron_right |
| SA-442/SA-442M SA-442/SA-442M (Pressure Vessel Plates, Carbon Steel, Improved Transition Properties) | 2 | chevron_right |
| SA-449 SA-449 (Specification for Hex Cap Screws, Bolts, and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use) | 11 | chevron_right |
| SA-451/SA-451M SA-451/SA-451M (Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature Service) | 14 | chevron_right |
| SA-452 SA-452 (Centrifugally Cast Austenitic Steel Cold-Wrought Pipe for High-Temperature Service) | 3 | chevron_right |
| SA-453/SA-453M SA-453/SA-453M (Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels) | 12 | chevron_right |
| SA-455/SA-455M SA-455/SA-455M (Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese) | 1 | chevron_right |
| SA-47/SA-47M SA-47/SA-47M (Specification for Ferritic Malleable Iron Castings) | 2 | chevron_right |
| SA-476/SA-476M SA-476/SA-476M (Ductile Iron Castings for Paper Mill Dryer Rolls) | 1 | chevron_right |
| SA-479/SA-479M SA-479/SA-479M (Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels) | 89 | chevron_right |
| SA-487/SA-487M SA-487/SA-487M (Specification for Steel Castings Suitable for Pressure Service) | 68 | chevron_right |
| SA-494/SA-494M SA-494/SA-494M (Specification for Castings, Nickel and Nickel Alloy) | 21 | chevron_right |
| SA-508/SA-508M SA-508/SA-508M (Specification for Quenched and Tempered Vacuum-Treated Carbon and Alloy Steel Forgings for Pressure Vessels) | 36 | chevron_right |
| SA-513/SA-513M SA-513/SA-513M (Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing) | 37 | chevron_right |
| SA-515/SA-515M SA-515/SA-515M (Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service) | 4 | chevron_right |
| SA-516/SA-516M SA-516/SA-516M (Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service) | 4 | chevron_right |
| SA-517/SA-517M SA-517/SA-517M (Pressure Vessel Plates, Alloy Steel, High Strength, Quenched and Tempered) | 10 | chevron_right |
| SA-522/SA-522M SA-522/SA-522M (Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service) | 2 | chevron_right |
| SA-524/SA-524M SA-524/SA-524M (Specification for Seamless Carbon Steel Pipe for Atmospheric and Lower Temperatures) | 2 | chevron_right |
| SA-53/SA-53M SA-53/SA-53M (Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless) | 5 | chevron_right |
| SA-533/SA-533M SA-533/SA-533M (Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel) | 15 | chevron_right |
| SA-537/SA-537M SA-537/SA-537M (Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel) | 3 | chevron_right |
| SA-540/SA-540M SA-540/SA-540M (Specification for Alloy-Steel Bolting for Special Applications) | 46 | chevron_right |
| SA-541/SA-541M SA-541/SA-541M (Quenched and Tempered Carbon and Alloy Steel Forgings for Pressure Vessel Components) | 36 | chevron_right |
| SA-542/SA-542M SA-542/SA-542M (Specification for Pressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum and Chromium-Molybdenum-Vanadium) | 22 | chevron_right |
| SA-543/SA-543M SA-543/SA-543M (Pressure Vessel Plates, Alloy Steel, Quenched and Tempered, Nickel-Chromium-Molybdenum) | 6 | chevron_right |
| SA-553/SA-553M SA-553/SA-553M (Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8 and 9 Percent Nickel) | 3 | chevron_right |
| SA-556/SA-556M SA-556/SA-556M (Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes) | 3 | chevron_right |
| SA-557/SA-557M SA-557/SA-557M (Electric-Resistance-Welded Carbon Steel Feedwater Heater Tubes) | 3 | chevron_right |
| SA-562/SA-562M SA-562/SA-562M (Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic Coatings) | 1 | chevron_right |
| SA-563 SA-563 (Carbon and Alloy Steel Nuts) | 14 | chevron_right |
| SA-564/SA-564M SA-564/SA-564M (Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes) | 21 | chevron_right |
| SA-568/SA-568M SA-568/SA-568M (Standard Specification for Steel, Sheet, Carbon, Structural and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for steel sheet in coils and cut lengths) | 63 | chevron_right |
| SA-571 SA-571 (Austenitic Ductile Iron Castings for Pressure-Containing Parts Suitable for Low-Temperature Service) | 1 | chevron_right |
| SA-572/SA-572M SA-572/SA-572M (Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel) | 40 | chevron_right |
| SA-574 SA-574 (Specification for Alloy Steel Socket-Head Cap Screws) | 10 | chevron_right |
| SA-587 SA-587 (Specification for Electric-Resistance-Welded Low-Carbon Steel Pipe for the Chemical Industry) | 1 | chevron_right |
| SA-592/SA-592M SA-592/SA-592M (Specification for High-Strength Quenched and Tempered Low-Alloy Steel Forged Fittings and Parts for Pressure Vessels) | 3 | chevron_right |
| SA-612/SA-612M SA-612/SA-612M (Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service) | 1 | chevron_right |
| SA-620/SA-620M SA-620/SA-620M (Steel Sheet, Carbon, Drawing Quality, Special Killed, Cold-Rolled) | 1 | chevron_right |
| SA-638/SA-638M SA-638/SA-638M (Specification for Precipitation Hardening Iron Base Superalloy Bars, Forgings, and Forging Stock for High-Temperature Service) | 3 | chevron_right |
| SA-645/SA-645M SA-645/SA-645M (Specification for Pressure Vessel Plates, 5% and 5.5% Nickel Alloy Steel, Specially Heat Treated) | 2 | chevron_right |
| SA-649/SA-649M SA-649/SA-649M (Specification for Forged Steel Rolls Used for Corrugating Paper Machinery) | 9 | chevron_right |
| SA-656/SA-656M SA-656/SA-656M (Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability) | 30 | chevron_right |
| SA-660 SA-660 (Specification for Centrifugally Cast Carbon Steel Pipe for High-Temperature Service) | 3 | chevron_right |
| SA-662/SA-662M SA-662/SA-662M (Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service) | 3 | chevron_right |
| SA-666 SA-666 (Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar) | 40 | chevron_right |
| SA-667/SA-667M SA-667/SA-667M (Specification for Centrifugally Cast Dual Metal (Gray and White Cast Iron) Cylinders) | 1 | chevron_right |
| SA-671/SA-671M SA-671/SA-671M (Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures) | 44 | chevron_right |
| SA-672/SA-672M SA-672/SA-672M (Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures) | 40 | chevron_right |
| SA-675/SA-675M SA-675/SA-675M (Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties) | 36 | chevron_right |
| SA-688/SA-688M SA-688/SA-688M (Specification for Seamless and Welded Austenitic Stainless Steel Feedwater Heater Tubes) | 27 | chevron_right |
| SA-691/SA-691M SA-691/SA-691M (Specification for Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures) | 14 | chevron_right |
| SA-693 SA-693 (Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip) | 24 | chevron_right |
| SA-695 SA-695 (Steel Bars, Carbon, Hot-Wrought, Special Quality, for Fluid Power Applications) | 2 | chevron_right |
| SA-696 SA-696 (Specification for Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping Components) | 2 | chevron_right |
| SA-705/SA-705M SA-705/SA-705M (Specification for Age-Hardening Stainless Steel Forgings) | 19 | chevron_right |
| SA-723/SA-723M SA-723/SA-723M (Standard Specification for Alloy Steel Forgings for High-Strength Pressure Component Application) | 18 | chevron_right |
| SA-724/SA-724M SA-724/SA-724M (Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for Welded Pressure Vessels) | 3 | chevron_right |
| SA-727/SA-727M SA-727/SA-727M (Specification for Carbon Steel Forgings, for Piping Components With Inherent Notch Toughness) | 1 | chevron_right |
| SA-731/SA-731M SA-731/SA-731M (Seamless, Welded Ferritic, and Martensitic Stainless Steel Pipe) | 8 | chevron_right |
| SA-736/SA-736M SA-736/SA-736M (Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel- Copper-Chromium-Molybdenum-Columbium (Niobium) Alloy Steel) | 5 | chevron_right |
| SA-737/SA-737M SA-737/SA-737M (Specification for Pressure Vessel Plates, High-Strength, Low-Alloy Steel) | 2 | chevron_right |
| SA-738/SA-738M SA-738/SA-738M (Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and Lower Temperature Service) | 5 | chevron_right |
| SA-739 SA-739 (Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or Both) | 2 | chevron_right |
| SA-747/SA-747M SA-747/SA-747M (Specification for Steel Castings, Stainless, Precipitation Hardening) | 4 | chevron_right |
| SA-748/SA-748M SA-748/SA-748M (Statically Cast Chilled White Iron-Gray Iron Dual Metal Rolls for Pressure Vessel Use) | 8 | chevron_right |
| SA-765/SA-765M SA-765/SA-765M (Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings With Mandatory Toughness Requirements) | 6 | chevron_right |
| SA-789/SA-789M SA-789/SA-789M (Specification for Seamless and Welded Ferritic /Austenitic Stainless Steel Tubing for General Service) | 28 | chevron_right |
| SA-790/SA-790M SA-790/SA-790M (Specification for Seamless and Welded Ferritic /Austenitic Stainless Steel Pipe) | 33 | chevron_right |
| SA-803/SA-803M SA-803/SA-803M (Specification for Seamless and Welded Ferritic Stainless Steel Feedwater Heater Tubes) | 10 | chevron_right |
| SA-812/SA-812M SA-812/SA-812M (Steel Sheet, High-Strength, Low-Alloy, Hot-Rolled, for Welded Layered Pressure Vessels) | 2 | chevron_right |
| SA-813/SA-813M SA-813/SA-813M (Specification for Single- or Double-Welded Austenitic Stainless Steel Pipe) | 64 | chevron_right |
| SA-814/SA-814M SA-814/SA-814M (Specification for Cold-Worked Welded Austenitic Stainless Steel Pipe) | 63 | chevron_right |
| SA-815/SA-815M SA-815/SA-815M (Specification for Wrought Ferritic, Ferritic /Austenitic, and Martensitic Stainless Steel Piping Fittings) | 36 | chevron_right |
| SA-832/SA-832M SA-832/SA-832M (Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Vanadium) | 3 | chevron_right |
| SA-836/SA-836M SA-836/SA-836M (Specification for Titanium-Stabilized Carbon Steel Forgings for Glass-Lined Piping and Pressure Vessel Service) | 1 | chevron_right |
| SA-841/SA-841M SA-841/SA-841M (Specification for Steel Plates for Pressure Vessels, Produced by the Thermo-Mechanical Control Process (TMCP)) | 14 | chevron_right |
| SA-859/SA-859M SA-859/SA-859M (Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components) | 3 | chevron_right |
| SA-874/SA-874M SA-874/SA-874M (Standard Specification for Ferritic Ductile Iron Castings Suitable for Low-Temperature Service) | 1 | chevron_right |
| SA-905 SA-905 (Specification for Steel Wire, Pressure Vessel Winding) | 2 | chevron_right |
| SA-965/SA-965M SA-965/SA-965M (Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts) | 57 | chevron_right |
| SA-988/SA-988M SA-988/SA-988M (Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service) | 32 | chevron_right |
| SA-989/SA-989M SA-989/SA-989M (Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service) | 5 | chevron_right |
| SA-995/SA-995M SA-995/SA-995M (Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts) | 24 | chevron_right |
| SB/EN 1706 SB/EN 1706 (Aluminum and Aluminum Alloys - Castings - Chemical Composition and Mechanical Properties) | 94 | chevron_right |
| SB-108/SB-108M SB-108/SB-108M (Specification for Aluminum-Alloy Permanent Mold Castings) | 33 | chevron_right |
| SB-111/SB-111M SB-111/SB-111M (Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock) | 26 | chevron_right |
| SB-127 SB-127 (Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip) | 1 | chevron_right |
| SB-135/SB-135M SB-135/SB-135M (Specification for Seamless Brass Tube) | 11 | chevron_right |
| SB-148 SB-148 (Specification for Aluminum-Bronze Sand Castings) | 23 | chevron_right |
| SB-150/SB-150M SB-150/SB-150M (Specification for Aluminum bronze rod, bar and shapes) | 10 | chevron_right |
| SB-151/SB-151M SB-151/SB-151M (Specification for Copper-nickel-zinc alloy (Nickel Silver) and copper-nickel rod and bar) | 10 | chevron_right |
| SB-152/SB-152M SB-152/SB-152M (Specification for Copper Sheet, Strip, Plate, and Rolled Bar) | 28 | chevron_right |
| SB-160 SB-160 (Specification for Nickel Rod and Bar) | 3 | chevron_right |
| SB-161 SB-161 (Nickel Seamless Pipe and Tube) | 2 | chevron_right |
| SB-162 SB-162 (Nickel Plate, Sheet, and Strip) | 2 | chevron_right |
| SB-163 SB-163 (Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes) | 20 | chevron_right |
| SB-164 SB-164 (Nickel-Copper Alloy Rod, Bar, and Wire) | 2 | chevron_right |
| SB-165 SB-165 (Specification for Nickel-Copper Alloy Seamless Pipe and Tube) | 1 | chevron_right |
| SB-166 SB-166 (Specification for Nickel-Chromium-Aluminum Alloy, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy, Rod, Bar, and Wire) | 12 | chevron_right |
| SB-167 SB-167 (Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, and N06045) and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Seamless Pipe and Tube) | 10 | chevron_right |
| SB-168 SB-168 (Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674), and Nickel-Chromium-Molybdenum-Copper Alloy (UNS N06235) Plate, Sheet, and Strip) | 12 | chevron_right |
| SB-169/SB-169M SB-169/SB-169M (Specification for Aluminum Bronze Sheet, Strip and Rolled Bar) | 2 | chevron_right |
| SB-171/SB-171M SB-171/SB-171M (Specification for Copper-Alloy Plate and Sheet for Pressure Vessels,Condensers, and Heat Exchangers) | 19 | chevron_right |
| SB-187/SB-187M SB-187/SB-187M (Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar, and Shapes) | 18 | chevron_right |
| SB-209/SB-209M SB-209/SB-209M (Specification for Aluminum and Aluminum-Alloy Sheet and Plate) | 47 | chevron_right |
| SB-210 SB-210 (Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes) | 21 | chevron_right |
| SB-211/SB-211M SB-211/SB-211M (Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire) | 22 | chevron_right |
| SB-221M SB-221M (Specification for Aluminum and Aluminum Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)) | 42 | chevron_right |
| SB-234 SB-234 (Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers) | 7 | chevron_right |
| SB-241/SB-241M SB-241/SB-241M (Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube) | 32 | chevron_right |
| SB-247 SB-247 (Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings) | 18 | chevron_right |
| SB-26/SB-26M SB-26/SB-26M (Specification for Aluminum-Alloy Sand Castings) | 28 | chevron_right |
| SB-265 SB-265 (Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate) | 41 | chevron_right |
| SB-271/SB-271M SB-271/SB-271M (Specification for Copper-Base Alloy Centrifugal Castings) | 40 | chevron_right |
| SB-283/SB-283M SB-283/SB-283M (Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)) | 49 | chevron_right |
| SB-308/SB-308M SB-308/SB-308M (Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles) | 1 | chevron_right |
| SB-315 SB-315 (Seamless Copper Alloy Pipe and Tube) | 5 | chevron_right |
| SB-333 SB-333 (Specification for Nickel-Molybdenum Alloy Plate, Sheet, and Strip) | 5 | chevron_right |
| SB-335 SB-335 (Specification for Nickel-Molybdenum Alloy Rod) | 5 | chevron_right |
| SB-337 SB-337 (Specification for Seamless and welded titanium and titanium alloy pipe) | 6 | chevron_right |
| SB-338 SB-338 (Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers) | 29 | chevron_right |
| SB-348/SB-348M SB-348/SB-348M (Specification for Titanium and Titanium Alloy Bars and Billets) | 39 | chevron_right |
| SB-359/SB-359M SB-359/SB-359M (Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins) | 22 | chevron_right |
| SB-367 SB-367 (Specification for Titanium and Titanium Alloy Castings) | 17 | chevron_right |
| SB-369 SB-369 (Specification for Copper-Nickel Alloy Castings) | 2 | chevron_right |
| SB-381 SB-381 (Specification for Titanium and Titanium Alloy Forgings) | 39 | chevron_right |
| SB-395/SB-395M SB-395/SB-395M (Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes) | 20 | chevron_right |
| SB-407 SB-407 (Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube) | 7 | chevron_right |
| SB-408 SB-408 (Specification for Nickel-Iron-Chromium Alloy Rod and Bar) | 5 | chevron_right |
| SB-409 SB-409 (Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip) | 5 | chevron_right |
| SB-42 SB-42 (Specification for Seamless Copper Pipe, Standard Sizes) | 5 | chevron_right |
| SB-423 SB-423 (Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825, N08221, and N06845) Seamless Pipe and Tube) | 2 | chevron_right |
| SB-424 SB-424 (Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825, UNS N08221, and UNS N06845) Plate, Sheet and Strip) | 3 | chevron_right |
| SB-425 SB-425 (Ni-Fe-Cr-Mo-Cu Alloy (UNS N08825 and UNS N08221) Rod and Bar) | 2 | chevron_right |
| SB-43 SB-43 (Specification for Seamless Red Brass Pipe, Standard Sizes) | 1 | chevron_right |
| SB-434 SB-434 (Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, UNS N10242) Plate, Sheet and Strip) | 2 | chevron_right |
| SB-435 SB-435 (UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Plate, Sheet, and Strip) | 4 | chevron_right |
| SB-443 SB-443 (Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625) and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219) Plate, Sheet, and Strip) | 3 | chevron_right |
| SB-444 SB-444 (Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625 and UNS N06852) and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219) Pipe and Tube) | 4 | chevron_right |
| SB-446 SB-446 (Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar) | 4 | chevron_right |
| SB-462 SB-462 (Specification for Forged or Rolled Nickel Alloy Pipe Flanges, Forged Fittings, and Valves and Parts for Corrosive High-Temperature Service) | 20 | chevron_right |
| SB-463 SB-463 (Specification for UNS N08020 Alloy Plate, Sheet, and Strip) | 3 | chevron_right |
| SB-464 SB-464 (Specification for Welded UNS N08020, N08024, and N08026 Alloy Pipe) | 3 | chevron_right |
| SB-466/SB-466M SB-466/SB-466M (Seamless Copper-Nickel Pipe and Tube) | 7 | chevron_right |
| SB-467 SB-467 (Specification for Welded Copper-Nickel Pipe) | 4 | chevron_right |
| SB-468 SB-468 (Standard Specification for Welded UNS N08020 Alloy Tubes) | 3 | chevron_right |
| SB-473 SB-473 (UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire) | 3 | chevron_right |
| SB-493/SB-493M SB-493/SB-493M (Specification for Zirconium and Zirconium Alloy Forgings) | 3 | chevron_right |
| SB-505/SB-505M SB-505/SB-505M (Specification for Copper Alloy Continuous Castings) | 58 | chevron_right |
| SB-511 SB-511 (Nickel-Iron-Chromium-Silicon Alloy Bars and Shapes) | 2 | chevron_right |
| SB-514 SB-514 (Specification for Welded Nickel-Iron-Chromium Alloy Pipe) | 3 | chevron_right |
| SB-515 SB-515 (Welded UNS N08120, UNS N08800, UNS N08810, and UNS N08811 Alloy Tubes) | 4 | chevron_right |
| SB-516 SB-516 (Specification for Welded Nickel-Chromium-Aluminum Alloy (UNS N06699) and Nickel-Chromium-Iron Alloy (UNS N06600, UNS N06601, UNS N06603, UNS N06025, UNS N06045, UNS N06690, AND UNS N06693) Tubes) | 8 | chevron_right |
| SB-517 SB-517 (Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045) Pipe) | 4 | chevron_right |
| SB-523/SB-523M SB-523/SB-523M (Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes) | 3 | chevron_right |
| SB-535 SB-535 (Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube) | 2 | chevron_right |
| SB-536 SB-536 (Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Plate, Sheet, and Strip) | 2 | chevron_right |
| SB-543/SB-543M SB-543/SB-543M (Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube) | 16 | chevron_right |
| SB-550/SB-550M SB-550/SB-550M (Zirconium and Zirconium Alloy Bar and Wire) | 3 | chevron_right |
| SB-551/SB-551M SB-551/SB-551M (Specification for Zirconium and Zirconium Alloy Strip, Sheet and Plate) | 5 | chevron_right |
| SB-564 SB-564 (Specification for Nickel Alloy Forgings) | 40 | chevron_right |
| SB-572 SB-572 (Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod) | 4 | chevron_right |
| SB-573 SB-573 (Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, N10242) Rod) | 2 | chevron_right |
| SB-574 SB-574 (Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod) | 15 | chevron_right |
| SB-575 SB-575 (Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and Strip) | 11 | chevron_right |
| SB-581 SB-581 (Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod) | 5 | chevron_right |
| SB-582 SB-582 (Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and Strip) | 4 | chevron_right |
| SB-584 SB-584 (Specification for Copper Alloy Sand Castings for General Applications) | 57 | chevron_right |
| SB-599 SB-599 (Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Plate, Sheet, and Strip) | 1 | chevron_right |
| SB-61 SB-61 (Specification for Steam or Valve Bronze Castings) | 1 | chevron_right |
| SB-619/SB-619M SB-619/SB-619M (Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe) | 28 | chevron_right |
| SB-62 SB-62 (Specification for Composition Bronze or Ounce Metal Castings) | 1 | chevron_right |
| SB-620 SB-620 (Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Plate, Sheet, and Strip) | 1 | chevron_right |
| SB-621 SB-621 (Specification for Nickel-Iron-Chromium-Molybdenum Alloy (UNS N08320) Rod) | 1 | chevron_right |
| SB-622 SB-622 (Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube) | 34 | chevron_right |
| SB-625 SB-625 (Specification for UNS N08925, UNS N08031, UNS N08034, UNS N08932, UNS N08926, UNS N08354, UNS N08830 and UNS R20033 Plate, Sheet, and Strip) | 9 | chevron_right |
| SB-626 SB-626 (Specification for Welded Nickel and Nickel-Cobalt Alloy Tube) | 29 | chevron_right |
| SB-637 SB-637 (Precipitation-Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service) | 18 | chevron_right |
| SB-649 SB-649 (Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925, UNS N08031, UNS N08034, UNS N08354, and UNS N08926), and Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire, and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire) | 8 | chevron_right |
| SB-653/SB-653M SB-653/SB-653M (Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings) | 6 | chevron_right |
| SB-658/SB-658M SB-658/SB-658M (Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe) | 3 | chevron_right |
| SB-668 SB-668 (Specification for UNS N08028 Seamless Pipe and Tube) | 1 | chevron_right |
| SB-672 SB-672 (Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Bar and Wire) | 1 | chevron_right |
| SB-673 SB-673 (Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe) | 4 | chevron_right |
| SB-674 SB-674 (Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Tube) | 4 | chevron_right |
| SB-675 SB-675 (UNS N08367 Welded Pipe) | 1 | chevron_right |
| SB-676 SB-676 (UNS N08367 Welded Tube) | 2 | chevron_right |
| SB-677 SB-677 (Standard Specification for Nickel-Iron-Chromium-Molybdenum and Iron-Nickel-Chromium-Molybdenum-Copper Seamless Pipe and Tube) | 4 | chevron_right |
| SB-688 SB-688 (Chromium-Nickel-Molybdenum-Iron (UNS N08366 and UNS N08367) Plate, Sheet, and Strip) | 2 | chevron_right |
| SB-690 SB-690 (Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Seamless Pipe and Tube) | 2 | chevron_right |
| SB-691 SB-691 (Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367) Rod, Bar, and Wire) | 2 | chevron_right |
| SB-704 SB-704 (Welded UNS N06625, UNS N06219 and UNS N08825 Alloy Tubes) | 3 | chevron_right |
| SB-705 SB-705 (Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe) | 4 | chevron_right |
| SB-706 SB-706 (Specification for Seamless Copper Alloy (UNS No. C69100) Pipe and Tube) | 1 | chevron_right |
| SB-709 SB-709 (Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028) Plate, Sheet, and Strip) | 1 | chevron_right |
| SB-710 SB-710 (Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe) | 2 | chevron_right |
| SB-729 SB-729 (Specification for Seamless Nickel-Iron-Chromium-Molybdenum-Copper Nickel Alloy Pipe and Tube) | 3 | chevron_right |
| SB-75/SB-75M SB-75/SB-75M (Specification for Seamless Copper Tube) | 7 | chevron_right |
| SB-752/SB-752M SB-752/SB-752M (Specification for Castings, Zirconium-base, Corrosion Resistant, for General Application) | 3 | chevron_right |
| SB-804 SB-804 (UNS N08367 and UNS N08926 Welded Pipe) | 2 | chevron_right |
| SB-815 SB-815 (Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Rod) | 1 | chevron_right |
| SB-818 SB-818 (Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy (UNS R31233) Plate, Sheet and Strip) | 1 | chevron_right |
| SB-834 SB-834 (Specification for pressure consolidated powder metallurgy Iron-Nickel -Chromium-Molybdenum (UNS N08367), Nickel-Chromium -Molybdenum-Columbium (Nb) (UNS N06625), Nickel -Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Columbium-Molybdenum (UNS N07718) Alloy Pipe Flanges, Fittings, Valves, and Parts) | 6 | chevron_right |
| SB-861 SB-861 (Titanium and Titanium Alloy Seamless Pipe) | 36 | chevron_right |
| SB-862 SB-862 (Titanium and Titanium Alloy Welded Pipe) | 34 | chevron_right |
| SB-928/SB-928M SB-928/SB-928M (Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service) | 5 | chevron_right |
| SB-956 SB-956 (Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins) | 16 | chevron_right |
| SB-96/SB-96M SB-96/SB-96M (Specification for Copper-Silicon Alloy Plate, Sheet, Strip and Rolled Bar for General Purposes and Pressure Vessels) | 3 | chevron_right |
| SB-98/SB-98M SB-98/SB-98M (Specification for Copper-Silicon Alloy Rod, Bar and Shapes) | 3 | chevron_right |
| SC-582 SC-582 (Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment) | 1 | chevron_right |
| SF-467M SF-467M (Specification for Nonferrous Nuts for General Use (Metric)) | 51 | chevron_right |
| SF-468M SF-468M (Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]) | 45 | chevron_right |
| SF-568M SF-568M (Specification for Carbon and alloy steel externally threaded metric fasteners) | 19 | chevron_right |
| SFA-5.1/SFA-5.1M SFA-5.1/SFA-5.1M (Specification for carbon steel electrodes for shielded metal arc welding) | 158 | chevron_right |
| SFA-5.10/SFA-5.10M SFA-5.10/SFA-5.10M (Specification for bare aluminum and aluminum-alloy welding electrodes and rods) | 74 | chevron_right |
| SFA-5.11/SFA-5.11M SFA-5.11/SFA-5.11M (Specification for nickel and nickel-alloy welding electrodes for shielded metal arc welding) | 41 | chevron_right |
| SFA-5.12/SFA-5.12M SFA-5.12/SFA-5.12M (Specification for tungsten and oxide dispersed tungsten electrodes for arc welding and cutting) | 20 | chevron_right |
| SFA-5.13/SFA-5.13M SFA-5.13/SFA-5.13M (Specification for surfacing electrodes for shielded metal arc welding) | 50 | chevron_right |
| SFA-5.14/SFA-5.14M SFA-5.14/SFA-5.14M (Specification for nickel and nickel-alloy bare welding electrodes and rods) | 58 | chevron_right |
| SFA-5.15 SFA-5.15 (Specification for welding electrodes and rods for cast iron) | 14 | chevron_right |
| SFA-5.16/SFA-5.16M SFA-5.16/SFA-5.16M (Specification for titanium and titanium-alloy welding electrodes and rods) | 32 | chevron_right |
| SFA-5.17/SFA-5.17M SFA-5.17/SFA-5.17M (Specification for carbon steel electrodes and fluxes for submerged arc welding) | 14 | chevron_right |
| SFA-5.18/SFA-5.18M SFA-5.18/SFA-5.18M (Specification for carbon steel electrodes and rods for gas shielded arc welding) | 54 | chevron_right |
| SFA-5.2/SFA-5.2M SFA-5.2/SFA-5.2M (Specification for carbon and low-alloy steel rods oxyfuel gas welding) | 14 | chevron_right |
| SFA-5.20/SFA-5.20M SFA-5.20/SFA-5.20M (Specification for carbon steel electrodes for flux cored arc welding) | 82 | chevron_right |
| SFA-5.21/SFA-5.21M SFA-5.21/SFA-5.21M (Specification for bare electrodes and rods for surfacing) | 61 | chevron_right |
| SFA-5.22/SFA-5.22M SFA-5.22/SFA-5.22M (Specification for stainless steel flux cored and metal cored welding electrodes and rods) | 209 | chevron_right |
| SFA-5.23/SFA-5.23M SFA-5.23/SFA-5.23M (Specification for low-alloy and high manganese steel electrodes and fluxes for submerged arc welding) | 186 | chevron_right |
| SFA-5.24/SFA-5.24M SFA-5.24/SFA-5.24M (Specification for zirconium and zirconium-alloy welding electrodes and rods) | 3 | chevron_right |
| SFA-5.25/SFA-5.25M SFA-5.25/SFA-5.25M (Specification for carbon and low-alloy steel electrodes and fluxes for electroslag welding) | 13 | chevron_right |
| SFA-5.26/SFA-5.26M SFA-5.26/SFA-5.26M (Specification for carbon and low-alloy steel electrodes for electrogas welding) | 15 | chevron_right |
| SFA-5.28/SFA-5.28M SFA-5.28/SFA-5.28M (Specification for low-alloy steel electrodes and rods for gas shielded arc welding) | 202 | chevron_right |
| SFA-5.29/SFA-5.29M SFA-5.29/SFA-5.29M (Specification for Low-Alloy Steel Electrodes for Flux Cored Arc Welding) | 528 | chevron_right |
| SFA-5.3/SFA-5.3M SFA-5.3/SFA-5.3M (Specification for aluminum and aluminum-alloy electrodes for shielded metal arc welding) | 3 | chevron_right |
| SFA-5.30/SFA-5.30M SFA-5.30/SFA-5.30M (Specification for consumable inserts) | 23 | chevron_right |
| SFA-5.34/SFA-5.34M SFA-5.34/SFA-5.34M (Specification for nickel-alloy flux cored and metal cored welding electrodes) | 55 | chevron_right |
| SFA-5.4/SFA-5.4M SFA-5.4/SFA-5.4M (Specification for stainless steel electrodes for shielded metal arc welding) | 200 | chevron_right |
| SFA-5.5/SFA-5.5M SFA-5.5/SFA-5.5M (Specification for low-alloy steel electrodes for shielded metal arc welding) | 308 | chevron_right |
| SFA-5.6/SFA-5.6M SFA-5.6/SFA-5.6M (Specification for copper and copper-alloy electrodes for shielded metal arc welding) | 9 | chevron_right |
| SFA-5.7/SFA-5.7M SFA-5.7/SFA-5.7M (Specification for copper and copper-alloy bare welding rods and electrodes) | 10 | chevron_right |
| SFA-5.8/SFA-5.8M SFA-5.8/SFA-5.8M (Specification for filler metals for brazing and braze welding) | 121 | chevron_right |
| SFA-5.9/SFA-5.9M SFA-5.9/SFA-5.9M (Specification for bare stainless steel welding electrodes and rods) | 74 | chevron_right |