PROPRIETARY CPM 9 V Tool steels

Material group: Ferrous Alloys / Tool steels
Country / Standard: PROPRIETARY

Data updates

Latest Update: 2025-09
Total number of updates: 2
Update History
2014-03

This material has 33 properties — only a subset is shown here.

Unlock full material properties, including detailed values across temperatures and conditions.

View Complete Material Data ›
Free registration required • Instant access

Free registration required • Instant access

PROPRIETARY CPM 9 V Chemical Composition

CRITERIA
VALUE
UNIT
CAS NUMBER
CRITERIA
C
VALUE
≤ 1.9000
UNIT
%
CAS NUMBER
7440-44-0
CRITERIA
Cr
VALUE
≤ 5.2500
UNIT
%
CAS NUMBER
7440-47-3
CRITERIA
Mn
VALUE
≤ 0.5000
UNIT
%
CAS NUMBER
7439-96-5
CRITERIA
Mo
VALUE
val1
Full data available with free access View Complete Material Data
UNIT
%
CAS NUMBER
7439-98-7
CRITERIA
Si
VALUE
val1
Full data available with free access View Complete Material Data
UNIT
%
CAS NUMBER
7440-21-3
CRITERIA
V
VALUE
val1
Full data available with free access View Complete Material Data
UNIT
%
CAS NUMBER
7440-62-2

ZAPP AG, Product Data Sheets,

Looking for full material performance data?

View Complete Material Data ›
Free registration required • Instant access

Free registration required • Instant access

PROPRIETARY CPM 9 V Physical Properties

Temperature

PROPERTY / VALUE
Modulus of Elasticity
190 — 221 GPa
Unlock full details
Full data available with free access View Complete Material Data
Density
7.4 — 8 kg/dm³
Unlock full details
Full data available with free access View Complete Material Data
Poisson Coefficient
val1
Full data available with free access View Complete Material Data
Unlock full details
Full data available with free access View Complete Material Data

This material has 33 properties — only a subset is shown here.

Unlock detailed physical values across temperatures and conditions.

View Complete Material Data ›
Free registration required • Instant access

Free registration required • Instant access

PROPRIETARY CPM 9 V Heat Treatments

  • SOFT ANNEALING The material is heated uniformly to a temperature of 880 - 900 °C; maintain temperature for 2 hours and allow to cool to 550 °C in the furnace at a cooling rate of 20 °C per hour. This is followed by cooling in still air. Hardening after annealing: approx. HB 220/ 250. STRES S RELIEVING Stress relieving follows rough machining by heating to 600 - 700 °C, holding time 2 hours. The material is subsequently allowed to cool in the furnace to approximately 500 °C, followed by cooling in air. HARDENING usually involves the use of 2 preheating stages (450 - 500 °C/ 850 - 900 °C). The material is then heated to the required austenitizing temperature in the range from 1070 °C to 1180 °C. QUENCHING hot bath quenching at approx. 550 °C. TEMPERING should be carried out immediately after the material has cooled down to below 40 °C or when the tool can be held with bare hands. Triple tempering with a holding time of 2 hours in each stage at the tempering temperature is necessary. It is important to ensure that the tools are cooled down to room temperature between the individual tempering stages. SURFACE TREATMENTS can be nitrided or PVD/ CVD coated.

PROPRIETARY CPM 9 V Mechanical Properties

Temperature

PROPERTY / VALUE
Brinell Hardness (HB)
223 — 255
Unlock full details
Full data available with free access View Complete Material Data

Need complete mechanical properties to make the right choice?

Get complete data on strength, hardness, fatigue, and more.

View Complete Material Data ›
Free registration required • Instant access

Free registration required • Instant access

Book A Demo

Optimize material selection for your application - Book A Demo

  • 3Cross References
  • 10Composition
  • 9Mechanical Properties
  • 7Physical Properties
  • 1Heat Treatment
  • 1Metallography
  • -Machinability
  • -Stress-Strain
  • -Formability
  • -Fatigue
  • -Fracture
  • -Creep
  • -Joints
  • -Coatings
  • -Dimensions
  • -Tribology
  • -Corrosion
  • -Ageing
  • -Weatherability
  • -Irradiation
  • 2Total Suppliers