PROPRIETARY VP20ISOF Werkzeugstähle
Datenaktualisierungen
Dieser Werkstoff verfügt über 12 Eigenschaften – hier wird nur ein Teil davon angezeigt.
Erhalten Sie Zugriff auf alle Werkstoffeigenschaften, einschließlich detaillierter Werte für verschiedene Temperaturen und Zustände.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY VP20ISOF Chemische Zusammensetzung
Villares Metals, Product Data Sheets,
Suchen Sie nach vollständigen Daten für Werkstoffe?
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY VP20ISOF Physikalische Eigenschaften
Temperatur
Dieser Werkstoff verfügt über 12 Eigenschaften – hier wird nur ein Teil davon angezeigt.
Erhalten Sie detaillierte physikalische Werte für verschiedene Temperaturen und Bedingungen.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
PROPRIETARY VP20ISOF Wärmebehandlung
- Annealing: Heat slowly and evenly to temperatures between 760 and 800°C, at a rate of 100ºC/h, keeping 1 hour for every 25 mm of the largest section of the piece. Slowly cool in an oven (30°C/h) to 600°C; then cool in calm air.
Stress Relief: Heating the molds slowly and evenly (100°C/h) up to 530°C, keeping 0.5 hour in temperature for each 25 mm of the largest section in the ask; regardless of the section, the time must not be less than 2 hours. After relief, cool in calm air.
Quenching: During quenching, the surface of the molds must be protected against decarburization and oxidation. Heat slowly and evenly at (100°C/h) up to 400°C and then at a maximum of 300°C/h until the austenitizing temperature, between 840 and 860°C. Keep at temperature until complete homogenization of the entire piece. Cooling must be carried out in oil suitable for quenching, stirred and heated between 40 and 70°C, until the mold temperature reaches 100°C. Then cool in calm air between 50 and 70°C.
Tempering: The tools must be tempered immediately after tempering, as soon as they reach 60°C. Make at least 2 tempers and between each temper the parts must cool slowly to room temperature. Tempering temperatures should be chosen as per desired hardness. The time of each tempering must be at least 2 hours. For pieces larger than 70 mm, the time must be calculated as a function of their dimension. Allow 1 hour for each mm of thickness.
Nitriding: Recommended when high levels of surface hardness and abrasion resistance are required. It must be carried out after quenching and tempering, as long as the nitriding temperature is at least 50°C lower than the temperature of the last tempering.
PROPRIETARY VP20ISOF Mechanische Eigenschaften
Temperatur
Benötigen Sie vollständige mechanische Eigenschaften, um die richtige Wahl zu treffen?
Erhalten Sie vollständige Daten zu Festigkeit, Härte, Ermüdung und mehr.
Kostenlose Registrierung erforderlich • Sofortiger Zugriff
Optimieren Sie die Materialauswahl für Ihre Anwendung - Demo vereinbaren
- 1Querverweise
- 4Zusammensetzung
- 1Mechanische Eigenschaften
- 3Physikalische Eigenschaften
- 2Wärmebehandlung
- -Metallographie
- -Zerspanbarkeit
- -Spannung-Dehnung
- -Umformbarkeit
- -Ermüdung
- -Fraktur
- -Schleicher
- -Verbindungen
- -Beschichtungen
- -Abmessungen
- -Tribologie
- -Korrosion
- -Alterung
- -Witterungsbeständigkeit
- -Bestrahlung
- 1Gesamtzahl der Lieferanten