Generic Ni-Resist 5 Dökme demir
Veri güncellemeleri
Bu malzemenin 22 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklıklar ve koşullar genelinde ayrıntılı değerler de dahil olmak üzere tam malzeme özelliklerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
Generic Ni-Resist 5 Kimyasal bileşim
Nickel Institute website - Technical Literature,
Tam malzeme performans verilerini mi arıyorsunuz?
Ücretsiz kayıt gereklidir • Anında erişim
Generic Ni-Resist 5 Fiziksel özellikler
Sıcaklık
Bu malzemenin 22 özelliği vardır - burada yalnızca bir alt kümesi gösterilmektedir.
Sıcaklık ve koşullar genelinde ayrıntılı fiziksel özellik değerlerinin kilidini açın.
Ücretsiz kayıt gereklidir • Anında erişim
Generic Ni-Resist 5 Isıl İşlem
- Stress relieve: This is done by heating to 600-650°C (1110-1200°F) at a rate of 50-100°C/hour (90-180°F/hour). The castings should be held in this temperature range for 2hours plus 1 hour per 25 mm (1 inch) of section thickness. They should then be furnace-cooled to or near ambient temperature. With castings made from Ni-resist alloys with the higher coefficients of expansion and with thin sections it is most important to have controlled, uniform heating and slow cooling.
High temperature stability: Castings intended for static or cyclic service at 480°C (900°F) and above can be given a dimensional stabilization heat treatment. If not done, carbon is slowly removed from the austenite matrix while at service temperatures. This results in a small growth in volume and distortion can occur. When the heat treatment is used this problem is eliminated. The proper cycle is to heat to 850-900°C (1560-1650°F) at 50-100°C (90-180°F) per hour. The castings should be held in this temperature range for not less than 2 hours plus 1 hour for each 25 mm (1 inch) of section thickness followed by air cooling.
Normalizing: The same heat treatment that is used for high-temperature stabilization can be used for normalizing. It will result in an increase in yield strength and elongation.
Annealing: If the castings of the correct composition are higher in hardness than expected, excessive carbide formation has probably occurred. Some softening and improved machinability can be achieved through high temperature annealing. This heat treatment will breakdown and/or spheroidize some of the carbides. To anneal, castings should be heated to 950-1025°C (1740-1875°F) at 50-100°C (90-180°F) per hour. They should be held in this temperature range for 2 hours per 25 mm (1 inch) of section thickness followed by cooling in the furnace or in still air.
Ambient temperature stability: For assured dimensional stability for service at ambient temperatures, slow, uniform heating to 815-840°C (1500-1560°F) if suggested. Castings should be held in this temperature range for one hour per 25 mm (1 inch) of section thickness and uniformly cooled to at least 315°C (600°F). For stringent requirements, the uniform cooling can be continued to ambient temperature.
Generic Ni-Resist 5 Mekanik özellikler
Sıcaklık
Doğru seçimi yapmak için eksiksiz mekanik özelliklere mi ihtiyacınız var?
Mukavemet, sertlik, yorulma ve daha fazlası hakkında eksiksiz verilere ulaşın.
Ücretsiz kayıt gereklidir • Anında erişim
Generic Ni-Resist 5 Uluslararası eşdeğer malzemeler
5 sonuçtan 2 tanesi gösteriliyor.
Eşdeğerlik kategorileri kimyasal bileşim ve mekanik özellik karşılaştırmasını yansıtır — uygulamanız için uygunluğu her zaman geçerli şartnameye göre doğrulayın.
5 uluslararası eşdeğerin tam listesine mi ihtiyacınız var?
Standart, üretici ve eşdeğerlik kategorisine göre ayrıntılı eşleştirme ile 5 eşdeğer kaliteyi görüntüleyin.
Ücretsiz kayıt gereklidir • Anında erişim
Uygulamanız için en uygun olan malzeme seçiminizi optimize edin - Demo Rezervasyonu Yapın
- 5Çapraz Referanslar
- 6Bileşim
- 4Mekanik Özellikler
- 5Fiziksel Özellikler
- 1Isıl İşlem
- -Metalografi
- -İşlenebilirlik
- -Gerilme-Gerinim
- -Şekillendirilebilirlik
- -Yorulma
- -Kırılma
- -Sürünmek
- -Bağlantılar
- -Kaplamalar
- -Boyutlar
- -Triboloji
- -Korozyon
- -Yaşlanma
- -Hava şartlarına dayanıklılık
- -Radyasyon etkisi
- 1Toplam Tedarikçiler