Najkompletnija baza podataka na svetu za materijale
• Ključne prednosti

### Koristi se u najrazličitijim oblastima

• Šta vam nudimo?

• Resursi

### Realizovano

DataPLUS, jedinstveni novi modul sa podacima o koroziji, spojevima, dimenzijama, tolerancijama i prevlakama pomaže još boljem izboru optimalnih materijala!

Kliknite za više detalja.

### Webinari

Introduction to Total Materia 7th February 2019

Introduction to Total Materia Integrator 7th March 2018

• O nama

Total Materia nam je omogućila da rešimo na nedvosmislen način sve probleme koje smo imali u vezi sa pretragom alternativnih materijala u stranim državama. Zahvaljujuci Total Materiji izdali smo stvarnu "međunarodnu" specifikaciju za nabavku čelika u stranim zemljama.

Total Materia ostaje jedino sredstvo koje ćemo koristiti u ove svrhe.

Massimo Manfredini
Bonfiglioli Industrial Gearmotors, Bolonja, Italija

Naša misija je jednostavna;
da Total Materia postane
prvi i jedini
izbor inženjera
širom sveta

Prof. Dr Viktor Pocajt, CEO
Key to Metals AG

# Fracture Mechanics: Part Three

Sažetak:

Linear elastic fracture mechanics (LEFM) principles are used to relate the stress magnitude and distribution near the crack tip to (1) remote stresses applied to the cracked component, (2) the crack size and shape, and (3) the material properties of the cracked component.

This article briefly describes background of Linear Elastic Fracture Mechanics.

### LEFM Assumptions

Linear elastic fracture mechanics (LEFM) is based on the application of the theory of elasticity to bodies containing cracks or defects. The assumptions used in elasticity are also inherent in the theory of LEFM: small displacements and general linearity between stresses and strains.

In the general form of the LEFM equations a singularity exists such that as r, the distance from the crack tip, tends toward zero, the stresses go to infinity. Since materials plastically deform as the yield stress is exceeded, a plastic zone will form near the crack tip.

The basis of LEFM remains valid, though, if this region of plasticity remains small in relation to the overall dimensions of the crack and cracked body.

There are generally three modes of loading, which involve different crack surface displacements (see Fig. 3). The three modes are:
 Mode 1: opening or tensile mode (the crack faces are pulled apart) Mode 2: sliding or in-plane shear (the crack surfaces slide over each other) Mode 3: tearing or anti-plane shear (the crack surfaces move parallel to the leading edge of the crack and relative to each other)

The following discussion deals with Mode 1 since this is the predominant loading mode in most engineering applications. Similar treatments can readily be extended to Modes 2 and 3.

### Stress Intensity Factor

The stress intensity factor, K, which was introduced in Eq. 1, defines the magnitude of the local stresses around the crack tip. This factor depends on loading, crack size, crack shape, and geometric boundaries, with the general form given by

 (2)

where:

s = remote stress applied to component (not to be confused with the local stresses, sij, in Eq. 1)
a = crack length
f (a/w) = correction factor that depends on specimen and crack geometry

Figure 4 gives the stress intensity relationships for a few of the more common loading conditions. Stress intensity factors for a single loading mode can be added algebraically. Consequently, stress intensity factors for complex loading conditions of the same mode can be determined from the superposition of simpler results, such as those readily obtainable from handbooks.

 Figure 4. Stress intensity factor for (a) Center-cracked plate loaded in tension, (b) Edge-cracked plate loaded in tension, (c) Double-edge-cracked plate loaded in tension (d) Cracked beam in pure bending

## Pretražite bazu znanja

Unesite reč za pretragu:

 Pretražite prema Kompletan tekst Ključne reči Naslovi Sažetak

 Ovaj članak pripada seriji članaka. Da biste pročitali više o ovoj temi, kliknite na linkove ispod.

Total Materia Extended Range predstavlja najveću bazu podataka o mehanici loma za više hiljada materijala i različitu termičku obradu. Podaci obuhvataju K1C, KC, rast prsline i Parisovu konstantu, a uključuju i dijagram rasta prsline.

Takođe, među podacima su i monotone osobine, kao i algoritam predviđanja podataka o mehanici loma na osnovu monotonih osobina.

Unesite materijal u odgovarajuće polje Brze pretrage. Pretragu možete suziti odabirom zemlje/standarda, a nakon toga kliknite na Pretražite.

Nakon što odaberete materijal sa liste rezultata otvoriće Vam se lista podgrupa po različitim standardima.

Pošto su Total Materia Extended Range podaci o mehanici loma neutralni u odnosu na specifikacije standarda, možete pregledati iste klikom na odgovarajući link u bilo kojoj podgrupi.

Podaci su predstavljeni u obliku tabele, a u pojedinim slučajevima Parisova konstanta je prikazana dijagramom (Region II). Za svaki zapis data je i odgovarajuća referenca.

Imate priliku da isprobate Total Materia bazu podataka. Pozivamo Vas da se pridružite zajednici od preko 150,000 registrovanih korisnika kroz Total Materia Besplatan demo.